Control Set-Up Procedures - Maytag MAT20PDFGW Instrucciones

Display
After the washer has been installed and plugged in, the display
will show "SYnC" for a few seconds, then "0 MINUTES." Once
the washer has been plugged in and the washer lid opened and
closed, the display will show the price. In washers set for free
cycles, the display will flash "SELECT CYCLE," and will display
"PRICE 0.00."
CYCLES
POWERWASH
NORMAL
DELICATES
NORMAL
ECO

Control Set-Up Procedures

IMPORTANT: Read all instructions before operating.
The top three keypads on the left side, the top keypad on the
right side, and the digital display are used to set up the controls.
The display can contain four numbers and/or letters and a
decimal point. These are used to indicate the set-up codes and
related code values available for use in programming the washer.
How to use the keypads to program the controls
1. The POWERWASH keypad is used to adjust the values
associated with set-up codes. Pressing the keypad will
increment the value.
Rapid adjustment is possible by holding the keypad down.
2. The NORMAL keypad will advance you through the
set-up codes. Pressing the keypad will advance you to
the next available set-up code. Holding the keypad down
will automatically advance through the set-up codes at a rate
of one (1) per second.
3. The DELICATES keypad is used to select or deselect options.
4. The TEMPERATURE keypad is used to decrease set-up code
value.
Start Operating Setup
PD Models: Insert access door key, turn, and lift to remove
n
access door.
PR models set for free vend: Refer to bottom of page for
n
operating setup.
IMPORTANT: The console must not be opened unless power
is first removed from the washer. To access connector J4:
g Unplug washer or disconnect power.
g Open console, disconnect plug on J4, close console.
g Plug in washer or reconnect power.
The washer is now in the set-up mode.
Before proceeding, it is worth noting that, despite all of the
options available, an owner can simply choose to uncrate a new
commercial washer, hook it up, plug it in, and have a unit that
operates.
Set-Up Codes
The set-up code is indicated by the one or two left-hand
characters. The set-up code value is indicated by the two
or three right-hand characters.
NOTE: Set-up codes marked with "*" are able to transfer from
one machine to another machine (must be same model type) via
USB stick.
CODE
6.xx
6.08
NORMAL
g Press the NORMAL keypad once to advance to next code.
OPTIONS
6.07
TEMPERATURE
DELICATES
SOIL LEVEL
EXTRA RINSE
g Press the NORMAL keypad once to advance to next code.
6.07
POWERWASH
g Press the NORMAL keypad once to advance to next code.
6.07
NORMAL
ECO
g Press the NORMAL keypad once to advance to next code.
7.00
7.00
g Press the NORMAL keypad once to advance to next code.
8.00
8.00
g Press the NORMAL keypad once to advance to next code.
9.00
9.00
9.0C
g Press the NORMAL keypad once to advance to next code.
1.00
1.00
1.0C
1.C0
g Press the NORMAL keypad once to advance to next code.
2.00
2.00
2.SP
If SPECIAL PRICING OPTION is selected, there is access to codes "3."
through "9.".
NOTE: An external battery needs to be added to keep the clock running during
periods of power outages.
g Press the NORMAL keypad once to advance to next code.
EXPLANATION
REGULAR CYCLE PRICE*
Amount to Start for NORMAL Cycle. Represents the number of
Coins or Debit pulses required to start the cycle. See Value of
Coin 1. Adjustable from 0 to 200.
PD models default setting is 8 - PR models default setting is 0.
Amount to Start for DELICATES Cycle. Represents the number of
Coins or Debit pulses required to start the base cycle. See Value
of Coin 1. Adjustable from 0 to 200.
PD models default setting is 7 - PR models default setting is 0.
Amount to Start for POWERWASH Cycle. Represents the number
of Coins or Debit pulses required to start the cycle. See Value of
Coin 1. Adjustable from 0 to 200.
PD models default setting is 7 - PR models default setting is 0.
Amount to Start for NORMAL ECO Cycle. Represents the number
of Coins or Debit pulses required to start the base cycle. See
Value of Coin 1. Adjustable from 0 to 200.
PD models default setting is 7 - PR models default setting is 0.
ADDITIONAL WASH TIME*
This is the number of minutes that can be added to a Wash Cycle.
Choose from 00–05 minutes by pressing the POWERWASH keypad.
ADDITIONAL RINSE TIME*
This is the number of minutes that can be added to a
RINSE Cycle. Choose from 00–05 minutes by pressing the
POWERWASH keypad.
CYCLE COUNTER OPTION*
This option is either SELECTED "ON" or NOT SELECTED "OFF."
Not Selected "OFF."
Selected "ON" and not able to be deselected.
Press the DELICATES keypad three consecutive times to select
"ON." Once selected "ON" it cannot be deselected.
MONEY COUNTER OPTION*
This option is either SELECTED "ON" or NOT SELECTED "OFF."
Not Selected "OFF."
Selected "ON."
Press the DELICATES keypad three consecutive times to select
"ON" and three consecutive times to remove (Not Selected
"OFF.") Counter resets by going from "OFF" to "ON."
Selected "ON" and not able to be deselected.
To select "ON" and not able to be deselected, first select "ON,"
then within two seconds press the DELICATES keypad twice,
the POWERWASH keypad once, and exit the set-up mode.
SPECIAL PRICING OPTION*
This option is either SELECTED "ON" or NOT SELECTED "OFF."
Not Selected "OFF."
Selected "ON." Press the DELICATES keypad once for this
selection.
15