Publicidad
Idiomas disponibles
Idiomas disponibles
3.
When all adjustments are done, press PTT switch (12) to store and exit. If the
KEY BEEP function is activated, a long beep sounds to confirm the success
of the operation (consul the KEY BEEP menu page 12).
4.
If no key is pressed for 10 seconds, the unit automatically exits the function
VOX SETTING without save.
Sensitivity
-
: allows the adjustment of the microphone (original one
or optional vox) for an optimum transmission quality. Adjustable level from1
(high level) to 9 (low level). Default value: 5.
-
Anti-Vox
: allows disabling the transmission generated by the
surrounding noise. The level is adjustable. AF (according the squelch level)
and from 0 (without anti-vox) to 9 (low level). Default value: AF.
-
Delay time
: allows avoiding the sudden cut of the transmission by
adding a delay at the end of speaking. The level is adjustable from 1 (short
delay) to 9 (long delay). Default value: 1.
VOX SETTING doesn't activate the VOX function.
CTCSS/DCS
For simplicity, in this manual we will speak of CODE to indicate both a CTCSS
tone and a DCS code, of GENRE to indicate the kind of code (CTCSS, DCS
or OFF = no code). TYPE indicates whether this is a TX transmission or an RX
reception and MODE specifies the operating mode, Identical I d or different
DF.
Consult the CODE SET menu page 14.
See list of codes page 67 and 68.
Note: Codes can only be used in FM. Each channel can have its own code.
-
Select the desired channel using the rotary CH knob (4) or the UP/DN buttons
(13) on the microphone.
-
Press the F key (8).
appears.
-
Press the VOX key (9) to activate/deactivate the CTCSS/DCS function.
Activation
If a CTCSS/DCS code has been stored, it becomes active, "CTCSS" or "DCS"
icon is displayed on the screen.
In I d mode, if no CTCSS/DCS code has been stored, the device emits an
error beep. Go to the CODE SET menu to store a CTCSS/DCS code.
In DF mode, if no CTCSS/DCS code has been stored in either type TX or type
RX, the device emits an error beep. Go to the CODE SET menu to store the
CTCSS/DCS codes.
Deactivation
If a CTCSS/DCS code has been stored and "CTCSS" or "DCS" is displayed
on the screen, a short press on the VOX key (9), after the F key (8), deacti-
vates the stored code, "CTCSS" or "DCS" disappears, a deactivation beep
sounds. The memorized CTCSS/DCS code is kept in memory but no longer
functions.
10) USB CHARGING SOCKET
The USB socket (10) can be used to charge smartphones, tablets or other
rechargeable devices with 5 V - 2.1 A.
11) 6 PIN MICROPHONE PLUG
The plug is located on the front panel of the transceiver and makes the
setting of the equipment into the dashboard easier.
See Cabling Diagram page 68.
12) PTT (Push To Talk)
Transmission key, press to transmit a message,
to listen to an incoming communication,
TOT (Time Out Timer)
If the transmission using PTT switch (12) or VOX function is longer than 3
minutes, the display starts blinking and the transmission ends. A beep will
sound until the PTT switch (12) key is released.
13) UP/DN BUTTONS ON MICROPHONE ~ SCAN
UP/DN BUTTONS ON MICROPHONE
Press UP/DN buttons (13) on the microphone to change the channel. UP to
increase and DN to decrease the channel.
See ROTARY KNOB page 8.
SCAN
(very long press)
CB CHANNELS SCAN
CB
In
mode, press and hold the UP or DN button (13) for ± 7 seconds or until
a beep sounds (consult the KEY BEEP menu page 12) to activate the 40
channels CB SCAN function. "SCN" appears on the display. The scanning
stops as soon as there is a busy channel. Consult the SCAN TYPE menu page
mode, turn the rotary CH knob (4) or press the UP/DN
13. In
SCANNING
buttons (13) on the microphone to change scan direction.
Press PTT switch (12) to exit CB CHANNEL SCAN. "SCN" disappears on the
display. See the § SKIP page 9.
10
is displayed and release
disappears.
(short press)
Publicidad
