Publicidad
Idiomas disponibles
Idiomas disponibles
EMG2
1.
Using the rotary CH knob (4) select a channel other than an emergency
channel. "EMG" must not appears on the display.
2.
Press the AM/FM key (5) to select the modulation mode of the selected
channel.
3.
Long press the EMG key (6).
message says:
.
4.
Turn the rotary CH knob (4) or use the UP/DN keys (13) on the microphone
to select the priority channel 2. The message says :
5.
Press the PTT switch (12) ou the F key (8) to validate and exit. If the KEY BEEP
function is activated, a long beep sounds to confirm the success of the
operation (consult then KEY BEEP menu page 12).
6.
If no key is pressed for 5 seconds, the unit automatically exits EMERGENCY
CHANNEL without save.
7) ANL/NB ~ HI-CUT ~ NRC
ANL/NB
(short press)
The ANL filter is enable only in AM mode.
Short press the ANL/NB key (7) to activate/deactivate the filters in this order:
The activated filter is shown on the display.
ANL - Automatic Noise Limiter / NB - Noise Blanker: These filters allows the
reduction of background noises and some reception interferences.
HI-CUT
(long press)
Long press the HI-CUT key (7) to activate/deactivate the HI-CUT filter. "HIC"
appears on the display when the filter is active.
Hi-Cut: Eliminates high frequency interferences. Has to be used in accor-
dance with the reception conditions.
NRC
(F key + short press)
This switchable filter improves the receive and transmit mode.
Press the F key (8).
-
appears in the display.
-
Press the NRC key (7) to activate/deactivate the NRC if a
than 0 has been stored (consult the NRC SET menu page 14), otherwise
the display indicates
When the NRC is active, "
" appears on the display.
appears on the display, "EMG" blinks. The
.
or value other
.
8) F ~ SKIP ~ MENU
F
(short press)
Allows to set/validate functions (see for example § VOX SETTING below).
This key pressed alone don't have any use.
See § TALKBACK page 11.
SKIP
(long press only if the CB CHANNEL SCAN function is activated)
This function allows you to skip a CB channel found by the SCAN function.
When the scan stops on an unwanted channel, press and hold the F key
(8) for 1 second to store this channel in the SCAN SKIP memory. A beep
sounds. The channel will no longer be scanned. See the § CB CHANNEL
SCAN page 10.
Consult the SCAN SKIP menu page 13 and the RESET menu page 15.
MENU
(short press + long press)
Short press the F key (8) firs time.
second time to enter the MENU
See § MENU page 11.
9) VOX ~ VOX SETTING ~ CTCSS/DCS
VOX
(short press)
The VOX function allows transmitting by speaking into the original micro-
phone (or in the optional vox microphone) without pressing the PTT switch
(12). The use of an optional vox microphone connected to the rear panel
of the transceiver (C) disables the original microphone.
Short press the VOX key (9) in order to activate the VOX function. "VOX"
appears on the display. Short press again the VOX key (9) to disable the
function. "VOX" disappears.
VOX SETTING
(long press)
1.
Long press the VOX key (9) to enter the VOX SETTING. "VOX" blinks, the
current setting and its value appear on the display. Three parameters allow
to adjust the VOX: Sensitivity
time
.
2a. Turn the rotary CH knob (4) or use the UP/DN key (13) on the microphone
to modify the current parameter then, press the F key (8) to select next
parameter or....
2b. Press first the F key (8) to select another the parameter and then turn the
rotary CH knob (4) or use the UP/DN key (13) on the microphone to modify
the current parameter.
9
is displayed. Long press the F key (8)
/ Anti-vox level
/ Vox delay
Publicidad
