Publicidad
Idiomas disponibles
Idiomas disponibles
WX CHANNELS SCAN
WX
In
mode, press and hold the UP or DN button (13) for ± 7 seconds or until
a beep sounds (consult the KEY BEEP menu page 12) to activate the 7
channels WX SCAN function. "SCN" appears on the display. The scanning
stops as soon as there is a busy channel. Consult the SCAN TYPE menu page
13. In
SCANNING
mode, turn the rotary CH knob (4) or press the UP/DN
buttons (13) on the microphone to change scan direction.
Long press the ANL/NB key (7) to exit WX CHANNELS SCAN. "SCN" disappears
on the display.
6 + 8) KEY LOCK
(EMG + F keys)
Long press simultaneously the EMG (6) and F (8) keys to activate/deactivate
the KEY LOCK function. When the function is active, "
display.
A) DC-POWER TERMINAL (13.8 V / 27.6 V)
B) ANTENNA CONNECTOR (SO-239)
C) JACK FOR OPTIONAL VOX MICROPHONE (Ø 2.5 mm)
D) PA SPEAKER JACK (8 Ω, Ø 3.5 mm)
E) JACK FOR EXTERNAL OPTIONAL SPEAKER (8 Ω, Ø 3.5 mm)
C) FUNCTIONS WITH THE PTT SWITCH
1) TALKBACK
This function allows you to hear your own modulation in the optional internal
or external speaker connected to the EXT.SP jack (E).
Press and hold the PTT switch (12) then press the F key (8) to activate /
deactivate the TALKBACK function.
When the function is active, "TALKBACK" blinks on the display for 3 seconds,
displaying the current level of the TALKBACK and then remains permanently
displayed.
2) TALKBACK LEVEL
This function allows to adjust the volume of the TALKBACK.
1.
Activate the TALKBACK function.
2.
Press and hold the PTT switch (12) then turn the rotary CH knob (4) to in-
crease (clockwise) / decrease (counterclockwise) the volume level of the
TALKBACK.
3.
Release the PTT switch (12).
3) NOISE GATE
Press and hold the PTT switch (12).
-
-
Short press the VOX key (9) to activate or deactivate the NOISE GATE.
"
" is displayed when the function is active.
Noise Gate: Prevents amplification of background noise. This results in
optimized signal levels.
D) MENU
The order of 14 menus is as described in this manual. However, the menu
displayed by entering the MENU will be the last menu modified by the user.
The procedure is the same whatever the function is:
" appears on the
Press F key (8).
Long press F key (8) to enter the MENU.
1.
Turn the rotary CH knob (4) or use UP/DN buttons (13) on the microphone
to select the menu to set.
2.
Press EMG key (6) to validate. The current value blinks on the display.
3.
Turn the rotary CH knob (4) or use UP/DN buttons (13) on the microphone
to modify the value of the parameter.
4.
New press on EMG key (6) to validate the chosen value. The parameter
stops blinking and if the function has more than one parameter, the next
parameter blinks.
5.
If no key is pressed, the unit exits MENU after 10 seconds.
from the display.
Note: UP/DN buttons (13) on the microphone have the same effect as the
rotation of the rotary CH knob (4). PTT switch (12) validates the last setting
and exists MENU.
1) COLOR
Press F key (8).
Long press F key (8) to enter the MENU.
1.
Turn the rotary CH knob (4) or use UP/DN buttons (13) on the microphone
to select the
2.
Press EMG key (6) to validate. The current color blinks on the display.
3.
Turn the rotary CH knob (4) or use UP/DN buttons (13) on the microphone
to modify the color of the display.
11
(PTT + VOX)
is displayed.
disappears.
is displayed.
menu.
disappears
Publicidad
