Publicidad
Idiomas disponibles
Idiomas disponibles
MENU activated
The channel is stored in the scan skip memory
Indicates the active channel
TX or RX bargarph
Indicates Frequency, Menu or Message
4) ROTARY KNOB
Turn the rotary CH knob (4) to adjust channel. Clockwise to increase, coun-
terclockwise to decrease the channel.
See § UP/DN BUTTONS ON THE MICROPHONE page 10.
5) AM/FM ~ PA ~ CB/WX ~ ALERT
AM/FM
(short press)
Press the AM/FM key (5) to modify the modulation mode AM or FM. Your
modulation mode has to correspond to the one of your correspondent.
Amplitude Modulation / AM: communication on a field with relief and
-
obstacles at middle distance (the most used).
-
Frequency Modulation / FM: for nearby communications on a flat open
field.
PA (Public Address)
(long press)
An external loud speaker can be connected to the unit by the PA jack plug
located on the back panel PA.SP. (D).
Long press PA key (5) to alternate between
button (1) to adjust the PA volume.
PA
For details on operating in
13.
CB/WX
(F key + short press)
Short press the F key (8) and short press the CB/WX key (5) to alternate be-
CB
WX
tween
or
(Weather Channel) mode. "WX" appears on the display
if the Weather Channel mode is active.
WX (Weather Channel) Mode
CB functions are not allowed in WX mode.
The WX mode allows you to hear weather informations. When the mode
is activated, use rotary CH knob (4) or the UP/DN buttons (13) on the mi-
CB
PA
mode. Turn the VOL
and
mode, consult the PA SETTING menu page
crophone to move through the 7 weather channels and find the active
channel in your local area. See table page 67.
The display shows the selected weather channel and if the unit receives a
signal,
icon appears.
ALERT
(F key + long press)
This function only works in CB mode. It does not work in WX mode.
Short press the F key (8) and press the Alert key (5) for 1 second to activate/
deactivate the ALERT function. When the function is activated and a tone
is detected at the selected weather channel, then the unit sounds a "siren"
alert. "ALERT" and the WX channel blink on the display. The unit cancels
WX
mode and goes to
mode.
While the "siren" sounds, press any key to stop the sound, "ALERT" and the
"WX channel" stop blinking on the display.
Note: The "siren" alert sounds when ALERT is detected in the selected
WEATHER channel only. Use first the SCAN function in
CHANNELS SCAN page 11) for detect alerts in all the weather channels.
6) EMERGENCY CHANNELS ~ STORE
EMERGENCY CHANNELS
Emergency channels will be automatically selected by pressing the EMG key
(6). First press : emergency channel 1 is activated. Second press: emergency
channel 2 is activated. Third press: return to the current channel. "EMG"
appears on the display when an emergency channel is activated.
Default emergency channels are channel 09/AM and channel 19/AM
STORE
(long press)
EMG1
1.
Using the rotary CH knob (4) select a channel other than an emergency
channel. "EMG" must not appears on the display.
2.
Press the AM/FM key (5) to select the modulation mode of the selected
channel AM OR FM.
3.
Long press the EMG key (6).
message says:
.
4.
Press the PTT switch (12) or the F key (8) to validate and exit. If the KEY BEEP
function is activated, a long beep sounds to confirm the success of the
operation (consult the KEY BEEP menu page 12).
5.
If no key is pressed for 5 seconds, the unit automatically exits EMERGENCY
CHANNEL without save.
8
WX
mode (see § WX
(short press)
appears on the display, "EMG" blinks. The
CB
Publicidad
