Oster BVSTEM7300 Manual De Instrucciones página 67

2.REMOVE
1.TURN
WARNING: Do not pour water or any other
liquid into the Grind Chamber.
• Cleaning & Unblocking Grind Outlet
CLEAR OF
COFFEE BEANS
- Feed the Cleaning Brush up into the Grind
& GRINDS
Outlet from below, wiping & brushing the
inside surfaces.
- If the Grind Outlet is clear the bristles will be
visible inside the Grind Chamber.
PRESIONAR Y MANTENER
ALIGN HOPPER GUIDE
HOPPER
GUIDE
ME
• Replace Top Burr
- Ensure the dot on the Top Cover aligns with
the dot on the Grinder Collar.
REMOVE
- Using the two handles insert the Top Burr
into the Grinder Collar.
- The arrows on the Top Burr should align to
ANDLE
arrows on the Grinder Collar.
- When correctly seated, the Top Burr will be
flush with the surface of the Grinder Collar.
TOP BURR
TOP COVER
GRINDER
COLLAR GRINDER
COLLAR
1.TURN
- Place handles flat, one on each side.
• Replace Bean Hopper
- Ensure the Hopper Guide is aligned with the
vertical white lines on the Hopper base.
- Align & insert the Bean Hopper into the
Grinder Collar and firmly pushing down turn
clockwise to lock into place and open the
Hopper Guide.
ALIGN HOPPER GUIDE
PUSH DOWN
HOPPER
HOPPER
GUIDE
GUIDE
THE SAME TIME
GRINDER
INTERLOCK
S
OWN GROUP HANDLE
BVSTEM7300-054_19ESM4 (LA).indd 28
AT THE SAME TIME
CARE & CLEANING - GRINDER
PUSH DOWN GROUP HANDLE
AIR TIGHT
CONTAINER
MOLINILLO
1. ALIGN & INSERT
2.TURN
2.REMOVE
GRINDER
BARISTA MAX
GRINDER
CLEAR OF
BARISTA MAX
COFFEE BEANS
& GRINDS
GRINDER
MANUAL SHOT
BARISTA MAX
MANUAL SHOT
1. ALIGN & INSERT
1. ALIGN
& INSERT
2.TURN
3.HOPPER GATES OPEN
REMOVE
GRINDER
BARISTA MAX
MANUAL SHOT
GRINDER
BARISTA MAX
MANUAL SHOT
S
- Reset to the Grinder Setting noted prior to
cleaning.
- Refill the Bean Hopper with coffee beans.
Note: After cleaning, the optimum Grind Setting
may have changed. To find the optimum Grind
Setting use the information on pages 13-14.
Adjusting Bottom Burr
The Conical Burrs are made of hardened
Stainless Steel for extra-long life. However, after
prolonged use, the Bottom Burr may require
adjustment to compensate for wear.
If the coffee grinds are too coarse when the
Grind Setting is below 2 and the espresso is
consistently under extracted, the Bottom Burr
may need adjusting.
Contact Oster (details are on the back page)
should you think that the Bottom Burr needs
adjustment.
Important: Prior to contacting Oster Customer
Care, please ensure that you are using freshly
roasted beans and that the Top Burr is seated
correctly. If the Top Burr is not seated correctly
the Grinder will produce coarse coffee grinds.
Grind off excess coffee beans and clean the Top
Burr & Grind Chamber.
Important: Old coffee beans, no matter the
Grind Setting, will have a fast extraction and will
AIR TIGHT
produce an under extracted tasting espresso.
CONTAINER
Note: Oster Customer Care may determine that
Bottom Burr adjustment shims are required. Do
not attempt to add shims without first consulting
Oster.
CLEAN
2.TURN
English - 28
CLEAN
CLEAN
REMOVE
TOP COVER
GRINDER
COLLAR
GRINDER
GRINDER
MANUAL SHOT
MAX
2.8 L
1 L
1 L
MIN
MIN
2.TURN
1. ALIGN
& INSERT
BARISTA MAX
BARISTA MAX
MAX
2.8 L
3. CENTER
6/26/19 09:34