Kärcher B 260 RI Manual De Instrucciones página 11

Symbols on the charger
DANGER
Risk of fire
When plugged into a socket or in the event of poor elec-
trical connection between the plug and the socket, the
charger plug and the socket used may get very hot.
Before plugging in the mains plug, make sure that the
socket is approved for a current of 16 A and that it is in
a technically sound condition.
Make sure that the mains plug is clean and in good con-
dition.
CAUTION
Do not operate the device together with other devices
on extension cables with multiple sockets.
Device description
Device overview, front
Illustration B
Steering wheel
1
Fresh water tank automatic filling system
2
Pre-sweeping unit hood***
3
Side brushes*
4
Driving motor
5
Squeegee blade holder
6
Squeegee blade
7
Suction bar
8
* Optional
*** Combo variant only
Device overview, rear
Illustration A
Overhead guard*
1
Flashing beacon*
2
Blue spotlight rear/ front*
3
Suction lance for DOSE detergent dosing unit*
4
Waste water tank cap
5
Fresh water drain hose
6
Waste water drain hose
7
Manual tank cleaning - spray gun
8
Suction hose
9
Suction beam ram protection*
10
Waste water tank inspection opening
11
Waste container***
12
Fresh water lid
13
Control panel
14
* Optional
*** Combo variant only
Device overview, seat
Illustration C
Detergent tray for DOSE detergent dosing unit*
1
Seat
2
Steering wheel knob
3
Weight adjustment lever
4
Seat length adjustment lever
5
* Optional
Device overview, waste water tank
Illustration D
Waste water tank support
1
Float
2
Waste water impact protection
3
Waste water tank cap
4
Coarse dirt basket
5
Turbine pre-filter
6
Waste water tank
7
Device overview, pedals
Illustration AP
Coarse dirt flap pedal
1
Brake pedal
2
Accelerator pedal
3
Device overview, pre-sweeping unit
Illustration E
Filter housing cover
1
Pre-sweeping unit hood***
2
Side brushes***
3
Filter housing
4
Sweep container
5
*** Combo variant only
Type plate
Illustration AJ
Type plate
1
Control panel
Illustration F
Program switch
1
Display
2
QR code for the how-to video
3
Info button for menu navigation in the display
4
Travel direction switch
5
2-stage horn
6
Cleaning solution ON/OFF
7
Side brush/side scrubbing deck ON/OFF (side
8
brush option with Combo variant)
Intelligent key
9
Maximum permissible gradient
10
Safety switch
11
Program switch
Illustration G
0
1
Device is switched off.
Transport travel
2
Drive to the operating location.
Eco program
3
Clean the floor wet (with a reduced water quantity
and a reduced brush speed) and vacuum up waste
water (with reduced suction power).
Scour and vacuum
4
Wet clean the floor and vacuum up the waste water.
Increased brush contact pressure
5
Clean the floor wet (with increased brush contact
pressure and increased water quantity) and vacu-
um up the waste water.
Scouring / pre-cleaning without vacuuming
6
Clean the floor wet and let the detergent act.
Suctioning
7
Vacuum up the dirty liquid.
Polishing
8
Polish the floor at a high brush speed without apply-
ing liquid.
Symbols on the device
Drain for fresh water
Drain for waste water
Fresh water
Fresh water tank automatic filling system
Removing the coarse dirt basket
English
Eyelet point
* Optional
Pictograms on the display
Battery full
Battery empty
Brake activated
Presweep facility activated
Water off
Detergent activated
Detergent empty
Fresh water 100%
Fresh water 0%
Installation
Batteries
Recommended batteries, chargers
Order no.
Battery set 2.815-108.0
Charger 4.035-191.0
Volume (m3)* 71.78
Air flow (m3/h)** 27.71
* Minimum volume of battery charging room
** Minimum air flow between battery charging room and
environment
Batteries and chargers are available from specialist
shops.
Maximum battery dimensions
Length Width
842 627 mm
The following must be observed when fitting the wet bat-
teries:
● The maximum battery dimensions must be ob-
served.
● The seat must be pivoted up when charging wet bat-
teries.
● The battery manufacturer's regulations must be ob-
served when charging wet batteries.
Installing and connecting batteries
The batteries are already installed in the Bp variant. If
you did not receive a Bp variant, the batteries were ret-
rofitted at the national company or at your trusted deal-
er. This may be for availability, time, cost, import,
service, transport or similar reasons to your advantage.
ATTENTION
Risk of damage to the control electronics!
The control electronics can be destroyed by reversing
the polarity of the battery connections.
Take care to ensure the correct polarity when connect-
ing the batteries.
1. Adjust the steering wheel position all the way for-
ward.
2. Pivot the seat forward.
3. Remove the seat stop screw.
4. Remove the plug of the seat contact switch and
push it back through the opening.
Illustration AO
Seat contact switch plug
1
Height
537 mm
11