Sammic CK-38V Manual De Instrucciones página 17

- An acoustic and visual signal can be configured to warn the user that a
certain level of force has been reached. This is useful to ensure that constant
force is applied to obtain uniform cutting.
- Pressing on the plunger increases the force until the acoustic signal sounds
or the bar can be seen, indicating that the desired level of force has been
reached. Maintain this load without increasing the force to obtain uniform
cutting throughout the process.
- To set the acoustic signal, hold down the reverse rotation button (16) for
3 seconds to access the menu with which to set the load level at which the
acoustic signal will sound. Press the same key 16 again to exit the menu.
Operation with the standard intake hopper (J) and plunger (M).
CK-35V/38V and CA-3V.
- The mallet (L) must be housed and locked in its hole. Rotate it anti-
clockwise to do so.
- Start the machine.
- Raise the plunger (M). The motor will stop.
- Insert the products into the standard hopper (J).
- The motor will start and the cutting process begin once the user begins
to press down on the plunger (M). Feed the product by gently lowering the
plunger (M). Repeat the process as many times as required.
- Press "Stop" (A) once production has finished.
Operation with the standard intake hopper (K) and plunger (M).
CK-45V/48V and CA-4V.
- The mallet (L) must be housed and locked in its hole. Rotate it anti-
clockwise to do so.
- Start the machine.
- Lift the plunger (M) and turn it anti-clockwise to release the food insertion
area of the standard hopper (K). The plunger (M) can be left resting on the
plunger support (M). The motor will stop.
- Insert the products into the standard hopper (K).
- The motor starts and the cutting process begins when the plunger (M)
is rotated clockwise. Feed the product by gently lowering the plunger (M).
Repeat the process as many times as required.
- Press "Stop" (4) to finish.
Operation with cylindrical hopper (L). CK-35V/38V, CK-45V/48V and
CA-3V/4V.
This Ø 55 mm hopper is used to cut long, cylinder-shaped vegetables such
as carrots, endives, cucumber, etc.
- Start the machine.
- Release the mallet (L) by rotating it clockwise.
- Insert the products through the hole and push them gently with the "Mallet"
(L). Repeat the process as many times as required.
- Press "Stop" (A) once production has finished.
IMPORTANT: Leave the mallet (L) inside the cylindrical hopper when
the latter is not in use.
Operation of the CK-35V/38V, CK- 45V/48V and CA-3V/4V with tube
head.
- The tube head is must be mounted and locked in place.
- Start the machine.
- Insert the products through the upper holes in the tube head. The cutter will
stop automatically after working for 30 minutes. To continue, press "Start" again.
- Press "Stop" (4) to finish.
"Cutter" operating mode. (CK-35V/38V, CK- 45V/48V and KE-5V/8V):
With the machine disconnected from the mains:
With the bayonet mechanism (Y) open (AA), place the "Cutter" accessory
on the motor block so that the three lugs are inserted into the holes of the
quick-lock mechanism. The handle must be placed just above the keypad
for the machine to operate. Close (Z) the bayonet mechanism (Y) to lock the
accessory on the motor block.
Fit the "Blade assembly" (T) and close the lid (U) by turning it anticlockwise
until it is engaged and locked. The lid (B) has a hole through which to feed
the product while the machine is operating and a scraper which, when
rotated, stirs the contents of the vessel (S) so that they are processed more
evenly.
When the machine is switched on the screen will display Icon No. 5
(represented by the rotor) together with the speed level and the associated
RPM. The speed can be adjusted with the motor running or stopped.
The motor starts when the "Start" key (A) is pressed and will run until the
same key is pressed again or the PULSE B key is held down. It also starts
and runs while the PULSE B key is held down. The icon rotates while the
motor is running.
The motor rotation direction can be reversed by pressing the C key, either
with the motor running or stopped. The associated icon appears on the
screen and the speed level is represented by the "-" sign, indicating reverse.
With the motor running the icon then rotates in the opposite direction.
Each time the bowl is fitted (with each new process) and the motor starts, a
counter appears that counts the duration of the process. This time is reset
only when the bowl is removed.
The countdown time can be set by pressing the CLOCK "D" key when
fitting the bowl. Accept by pressing the same key again or starting the
motor. The countdown will then start. The timer has an associated indicator
circle (2) that provides a visual reference of the time remaining until the end
of the process. When the time reaches zero the motor stops and a "beep"
is emitted.
FORCE CONTROL function
With the motor running, ring 3 on the screen indicates load under which it
is working. When the indicator approaches the red zone, it means that the
motor is nearing overload. This level varies depending on the features of the
product being processed.
Dedicated programmes
With the motor stopped, press the DOWN button (12) until you reach
the dedicated programmes P1 (dense texture), P2 (light texture), and P3
(pulses). P1 and P2 are automatic programmes used to obtain a fine and
consistent grind. The pre-set time can be changed by pressing the TIME
button (13) (when the motor is stopped). P3 is a program of pulses, and it is
possible to change the number of pulses produced with the button TIME (13).
Press the START button (14) to start it up.
P1 (dense texture) for banana-type products.
P2 (light texture) for tomato-type products.
CLEANING
Cleaning of the "Vegetable Cutter" accessory CK-35V/38V, CK- 45V/48V
and CA-3V/4V:
- Release the lock (I) and open the hinged cover (J).
- On the CK-45V/48V and CA-4V, holding the disk (A) with your hand without
touching the blades, use the key (P) supplied with the machine to remove the
bit (Q) or the mixer (R), unscrewing it anticlockwise.
- Remove the disk (A) by turning it clockwise and carefully pulling it upwards.
Remove the grid (B) and the ejector (C).
- In the CK-35V/38V and CA-3V the plunger (M) and hinged lid (J) can be
dismantled for cleaning. The pins (N and O) must be removed to do so.
- 17 -
EN