GYS EXAGON 400 FLEX CC/CV Manual Del Usuario página 20

MODE SELECTION
Press the button several times until the LED light switches on below the
symbol .
WELDING STETTINGS
1. Welding intensity settings :
Adjust the welding current using the main knob
meter and the type of assembly to be carried out. The current setpoint is
indicated on the right side display.
2. Welding downslope settings :
Adjust the downslope duration using the secondary knob
tor shows the chosen settings, the right display indicates the precise downs-
lope duration in seconds.
ARC STRIKE / IGNITION :
LIFT start : Using the torch, make contact between the electrode and the metal piece, then slightly lift the electrode to start the arc.
WELD STOP / SWITCHING TO DOWNSLOPE :
To stop the weld, slightly lift the torch, the intensity will gradually reduce (downslope).
ASSISTANCE FOR SETTING UP AND SELECTING CONSUMABLES
0.3 - 3 mm
DC
2.4 - 6 mm
4 - 8 mm
6.8 - 8.8 mm
9 - 12 mm
ELECTRODE GRINDING
d
SEMI-AUTOMATIC MIG / MAG WELDING WITH VOLTAGE DETECTING WIRE FEEDER (
CONNECTIONS AND RECOMMENDATIONS
• Connect the earth clamp on the positive (+) or negative (-) terminal depending on the wire type
• Connect the wire feeder on the connector using a male-female cable (NOMAD CABLE),
• Refer to the wire feeder's user manual for the remaining connections.
MODE SELECTION AND SETTINGS
Press the button several times until the LED light switches on below the
symbol .
1. Setting the welding voltage :
Adjust the welding voltage using the main knob
to be carried out. The voltage setpoint is indicated on the left side display.
2. Inductance settings :
Adjust the inductance level using the second knob
-9 to +9. The lower the inductance level, the harder and more guiding the arc.
The higher the inductance and the softer the arc with little splatter.
CARBON ARC GOUGING
CONNECTIONS AND RECOMMENDATIONS
• Connect the earth clamp on the negative (-) terminal
• Connect the gouging torch on the positive (+) terminal
• Orient the clamp depending on the working position, make sure that the compressed air flows in the arc's direction and not the other way around.
• Place a carbon electrode,
• Connect the compressed air to the gouging torch,
The arc strike is easier : just make contact with the piece, and advance while pushing the electrodes towards the metal to be removed.
20
EXAGON 400 FLEX CC/CV
according to the dia-
. The indica-
Current (A) Electrode (mm)
5 - 75
60 - 150
100 - 200
170 - 250
255 - 300
L = 3 x d for a low current.
L = 3 x d for a high current
L
depending on the work
, a relative value from
VRD
V
ARC FORCE
INDUCTANCE
The grey areas are not useful for this mode.
Shroud (mm)
1 6.5
1.6 8
2 9.5
2.4 11
3.2 12.5
(in general on the -)
VRD
V
The grey areas are not useful for this mode.
MMA MIG
A
press 3 s
Basic
7018
CV
0
Rutile
6013
Cellulosic
6010
press 3s
setup
-9 +9
memory
Argon flow rate (L/min)
6 - 7
6 - 7
7 - 8
8 - 9
9 - 10
)
,
MMA
A
press 3 s
Basic
7018
0
Rutile
6013
Cellulosic
6010
ARC FORCE
INDUCTANCE
press 3s
-9 +9
EN
TIG Gouging
MODE
press 3s
MIG TIG Gouging
CV
MODE
press 3s
setup
memory