Installation; Assembling The Equipment; Upgrading The Wheel Aligner Software - Corghi EXACT 70 II Manual De Uso

Tabla de contenido

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

The warranties on the monitor, personal com-
puter and printer are no longer valid if the
original packaging is missing.

INSTALLATION

WARNING
Carry out the unpacking, assembly, lifting and
installation operations described with care.
Failure to comply with these recommendations
may damage the equipment and put the opera-
tor's safety at risk.

Assembling the equipment

- Unpack the equipment, placing the crate as
indicated above.
- Remove the rear panel of the cabinet.
- Remove the PC from the crate.
- Place the computer on the centre shelf (Fig.
7) via the front hatch.
For correct positioning, place the front part of
the computer level with the front of the shelf.
- Remove the monitor from its packaging (Fig.
3).
- Place the monitor on top of the cabinet and
connect the video cable to the PC (B, Fig. 9).
- Installing the electrical connector panel
(concentrator board): Install the electrical
connector panel at the bottom of the cabinet
(A, Fig. 8). The electrical connector panel must
be connected to the HDD power cables lead-
ing out of the back of the PC and to the Hard
Lock device with a USB cable (G, F, Fig. 9).
- Installing the Hard Lock device: Insert the
tip of a pen into the hole at the side to open
the SIM holder.
- Remove the wheel aligner SIM card (Fig. 50)
from its punched backing card (keep the
backing card with the serial number for future
queries) and insert in the SIM holder (Fig. 51),
with the gold contacts facing upward. Push the
SIM holder in.
Fix the Hard Lock device (B, Fig. 5) onto the back
of the cabinet with the relative fastener screws.
Connect the 2 USB cables to the Hard Lock device.
Connect the first cable to a free USB port on the
PC. Connect the second cable to the USB port
on the electrical connector panel (concentrator
board) (E,F, Fig. 9).
50
- Remove the printer from its packaging, place
inside the cabinet and connect the power and
USB cables.
- Remove the keypad from its packaging and
connect to one of the free USB ports at the
back of the PC (D, Fig. 9).
Connect the power cables to the multiple connec-
tor on the electrical connector panel (B, Fig. 8).
- Connect the cables with the aid of the wiring
diagram (Fig. 52); all the plugs are clearly in-
dicated on their respective PC sockets. Push
the plugs in completely without straining and,
where applicable, tighten the lock screws
- The wheel aligner is factory set to operate with
a 230 V AC power supply. The wheel aligner
may, however, be configured to operate with
115 V AC mains voltage.
If present, set the PC voltage setting switch
for the correct mains voltage.
- Refit the rear cover.
- Connect the power supply cable to the plug
provided; first read the "Electrical Hook-up"
section.
- Power up the PC, the monitor and the printer
with the switches provided.
- Update the wheel aligner software if neces-
sary, "Updating the Wheel Aligner Software"
section, and install any optional kits, "Installing
Additional Functions" section.
ATTENTION
For technical specifications, precautions, main-
tenance and all other information concerning
the monitor or printer, refer to the relative
operator's manuals supplied with the equip-
ment's documentation.
Upgrading the wheel aligner
software
The wheel aligner is supplied with the software
already installed, and is complete with an instal-
lation CD-ROM.
After installing the EXACT 70 wheel aligner switch
the equipment on and locate the initial screen.
Press the key combination È+ F12 (upper case
+ F12): the software version will appear on the
top left of the screen, beneath the CORGHI logo.
Compare the software release (indicated as "SW
Operator's Manual EXACT 70 II

Publicidad

Tabla de contenido
loading

Tabla de contenido