cecotec DRUMFIT CROSSFIT 1000 EOLO Manual De Instrucciones página 25

ENGLISH
1. PARTS AND COMPONENTS
Fig. 1
No. DESCRIPTION QUANT.
1 Main frame 1
2 Rear stabiliser 1
3 Front stabiliser 1
4L Handlebar (L) 1
4R Handlebar (R) 1
5L Connecting arm (L) 1
5R Connecting arm (R) 1
6 Saddle post 1
7 Console bracket 64×21×2.5 1
8 Rear stabiliser trim cap 2
9 Front stabiliser trim cap 2
10 Threaded bolt M8×40 2
11 Warped washer ø8×ø20×1.5 2
12 Domed nut M8 2
Hexagon bolt with internal
13 flat head M5×15 5
14 Warped washer ø5×ø14×δ1.0 5
15 Nylon nut M8 7
16 Flat washer ø8×ø16×δ1.5 5
Seat cushion
17 1
18L Pedal (L) 1
18R Pedal (R) 1
48 DRUMFIT CROSSFIT 1000 EOLO
No. DESCRIPTION QUANT.
18R Pedal (R) 1
Pedal bearing ø21×ø13×10
19 2
20 Plain washer ø18×ø34×2.5 2
Crank hub ø31×ø29×ø13×11
21 2
Nylon nut 1/2" /L
22L 1
Nylon nut 11/2" /R
22R 1
Saddle height-adjustment
23 knob M12 1
Hexagon bolt with internal
24 flat head M8×45 2
Hub ø18×ø14×ø8×ø10
25 2
26 Seat post spring 1
Ferrule
27 ø25×ø22.2×ø16.3×15 6
Nut cap ø24×13
28 2
Plain washer ø8×ø24×δ2.0
29 2
30 Long shaft ø16×260×M8 1
31 Console 1
Foam handle ø23×ø33×280
32 2
Plug ø25
33 4
Sensor L= 500 mm
34 1
Curved washer
35 ø17×ø22×δ0.3 2
Tools
- Hexagonal multi-function spanner with star tip. Fig. 2
4 mm Allen key. Fig. 3
-
Hexagonal multi-function spanner. Fig. 4
-
NOTE:
the graphics in this manual are schematic representations and may not exactly match the
device.
2. BEFORE USE
This appliance is packaged in a way as to protect it during transport. Take the device out
-
of its box and remove all packaging materials. You can keep the original box and other
packaging elements in a safe place. This will help you prevent damage to the device when
transporting it in the future. In case the original packaging is disposed of, make sure all
packaging materials are recycled accordingly.
Make sure all parts and components are included and in good conditions. If there is any
-
piece missing or in bad conditions, contact the official Cecotec Technical Support Service
immediately.
Box content
- Drumfit CrossFit 1000 Eolo exercise air bike
- Instruction manual
Tools and screws
-
AA batteries
-
3. PRODUCT ASSEMBLY
Front and rear stabilisers installation Fig. 5
Remove four hexagon bolts with internal flat head (13) and four warped washers
-
φ5×φ14×δ1.0 (14) from the rear stabiliser (2). Fix the rear stabiliser (2) to the main frame (1)
with four hexagon bolts with internal flat head (13) and four warped washers φ5×φ14×δ1.0
(14). Tighten the bolts using the Allen key provided.
Fix the front stabiliser (3) to the main frame (1) with two threaded bolts M8×40 (10), two
-
warped washers φ8×φ20×δ1.5 (11) and two domed nuts (12). Tighten the bolts with the
hexagonal multi-purpose tool provided.
Left and right handlebar installation Fig. 6
Remove two nylon nuts M8 (15), two plain washers φ8×φ24×δ2.0 (29) and two curved
-
ENGLISH
DRUMFIT CROSSFIT 1000 EOLO 49