Publicidad
Idiomas disponibles
Idiomas disponibles
Other pans, with aluminum inserts
in the base have a smaller area of
ferromagnetic material (see fig.4).
In this case, it may be difficult or
even impossible to detect the pan. In
addition, the power supplied may be
lower and, consequently, the pan will
not heat up correctly.
Fig. 4
Influence of the base of the pans
The type of base used on the pan
may affect the uniformity and results
of the cooking. Pans with a stainless
steel "sandwich" base use materials
that assist the uniform distribution
and diffusion of the heat, resulting in
savings in time and energy
The base of the pan must be
completely flat, thus ensuring a
uniform power supply (see fig.5).
Fig. 5
Never heat empty pans, or use
pans with a thin base, as these may
heat up quickly without allowing time
for the automatic disconnection
function of the cooker to come into
operation.
I M P O R T A N T
RECOMMENDATIONS:
Use vessels with the same base
diameter as that of the cooking zone.
In the cooking zones closest to
the control panel, always keep the
vessels within the cooking marks
indicated on the glass surface and
use vessels of the same or smaller
diameter to these. This will help to
prevent overheating in the control
zone.
Use the rear cooking zones for
intensive use of the appliance. This
will help to prevent overheating of the
control panel.
Do not allow the vessels to invade
the control panel zone, especially
during cooking.
Use and
Maintenance
User instructions of the
Touch Control
HANDLING ELEMENTS (fig. 1)
1 General on/off sensor.
2 Cursor slider for controlling power.
3
Power and/or residual heat
indicator*.
4 Decimal dot of power and/of
residual heat indicator.
5 Direct access to "Power" function.
6 Activation sensor for "Block"
function.
7 Activation sensor for "Flex Zone"
function.
8 Pilot indicator light "Block" or "Flex
Zone" function activated*.
9 Activation sensor for "Chef"
functions.
10 "Minus" sensor for timer.
11 "Plus" sensor for timer.
12 Timer indicator.
13 Decimal dot of the timer.*
14 Pilot indicator light "Simmering"
function activated*.
15 Pilot indicator light" Melting"
function activated*.
16 Pilot indicator light "Keep Warm"
function activated*.
17 Pilot indicator light "Slide Cooking"
function activated*.
Pilot indicator light "Grilling"
18
function activated*.
Pilot indicator light "Pan Frying"
19
function activated*.
Pilot indicator light "Frying"
20
function activated*.
Pilot indicator light "Poaching"
21
function activated*.
Pilot indicator light "Confit"
22
function activated*.
* Only visible while running.
The manoeuvres are done by means
of the touch keys. You do not need
to exert force on the desired touch
key, you only need to touch it with
your fingertip to activate the required
function
Each action is verified by a beep.
Use the cursor slider (2) to adjust
power levels (0 - 9) by sliding your
finger over it. Sliding towards the right
increases the value, whereas sliding
towards the left decreases it.
It's also possible to directly select a
power level by placing your finger
directly on a desired point of the cursor
slider (2)
In order to select a plate on
these models, directly touch the
cursor slider (2).
SWITCHING ON THE DEVICE
1 Touch the On touch key
least one second. The touch control
will become active, a beep will be
heard and the indicators (3) will light
up displaying a "-". If any cooking
area is hot, the related indicator will
flash an H.
If you do not take any action in the
next 10 seconds the touch control will
switch off automatically.
When the touch control is activated,
you can disconnect it at any time by
touching the touch button
if it has been locked (lock function
activated). The touch button
always has priority to disconnect the
touch control.
ACTIVATING PLATES
Once the Touch Control is activated
with sensor
(1), any plate can be
turned on by following these steps:
1 Slide the finger or touch in any
position of one of the cursors
"slider" (2). The zone has been
selected and simultaneuously the
power level will be set between 0
and 9. That power value will be
shown on the corresponding power
indicator and its decimal dot (4) will
keep light up during 10 seconds.
EN
(1) for at
(1), even
(1)
39
Publicidad
