Publicidad
Idiomas disponibles
Idiomas disponibles
ENGLISH
5. CLEANING AND MAINTENANCE
•
Make sure the product is not plugged in the power supply or on before cleaning or
maintenance.
•
Use a soft cloth to clean the exterior housing of the electric scooter.
•
Never use alcohol, petrol, paraffin, corrosive, or abrasive products to clean the electric
scooter.
•
Never immerse the electric scooter in water or any other liquid to clean it, as this could
damage the electronic parts permanently.
•
Never use pressurised water to clean the electric scooter.
•
Do not try to repair the electric scooter on your own. In case it does not operate correctly
or it is damaged, please, contact Cecotec Technical Support Service.
•
Self-tapping nuts and other fasteners may loosen their hold and need to be retightened.
•
If the scooter is expected to be inactive for more than 30 days, fully charge the battery
and place it in a cool, dry place. Remember to recharge it every 60 days to protect the
battery from possible damage beyond the scope of the warranty.
•
Disassembly of the wheels is complicated and improper assembly can cause instability
and malfunction.
Brake disc
You must check the brake discs are in perfect condition, matching the brake calliper, to set
this easily there is an Allen key included. Brake pads are consumable parts and must be
replaced when its shelf life expires.
Storage
•
When not in use, store the scooter in a dry and ventilated place. Do not leave it outdoors
for a long time. Excessive sunlight, overheating and overcooling accelerate tyre ageing
and compromise the service life of the scooter and its battery.
•
Charge it only if the room temperature is between 0ºC and 35ºC and store it at a
temperature between -10ºC and 35ºC.
Battery release
•
Battery removal is complicated and may alter the functioning of the electric scooter:
you can contact an authorised repair entity if the product warranty is still valid. If the
warranty has expired, you can contact a specialist workshop of your choice. You can also
contact the Cecotec Customer Service Department.
•
For proper removal of the battery for subsequent recycling, you must:
1.
Remove the anti-slip rubber from the top of the scooter.
2.
Loosen the screws on the upper part of the scooter.
3.
Unscrew the rear retaining stops.
4.
Remove the plastic part from the upper part.
66
ORIGINAL MANUAL TRANSLATION
5.
Remove the metal plate protecting the electronic components.
•
The external flexible cord of this appliance cannot be replaced; if the cord is damaged,
the appliance must be replaced with a new one. Note: The fully charged Bongo X65
Series Connected electric scooter has a battery life of 120-180 hours. The built-in smart
chip will keep track of your charges and discharges. Damage caused by prolonged
non-charging is irreversible and is not covered by warranty. Once damaged, the battery
cannot be recharged (disassembly by non-professionals is prohibited as it may cause
electric shock, short circuit or even serious health accidents).
6. TROUBLESHOOTING
If the electric scooter displays any of the following error codes, you should not attempt to
disassemble or repair the electric scooter yourself. Repairs carried out by unqualified persons
may result in injury or serious malfunctions. Please contact the place where you bought the
appliance or the official Cecotec Technical Support Service. The repair must be carried out by
an authorised technician and you must use only original spare parts.
P0: Battery overheating protection
P1: Display overheating protection
E0: Fault in the communication
E1: Accelerator failure
E2: Electric brake failure:
E3: Motor Hall sensor failure
E4: Motor failure
E5: Display failure
E6: Failure of battery wiring
E7: Gyroscope failure
7. TECHNICAL SPECIFICATIONS
Reference:
07109
Product:
Electric scooter X65 Connected series
Features
Measuring units
Dimensions
Folded
Unfolded
ENGLISH
Specifications
118x60x50,5 cm
118x60x124 cm (1)
BONGO SERIE X65
67
Publicidad
