Publicidad
Idiomas disponibles
Idiomas disponibles
ENGLISH
4. OPERATION
Assembly and configuration
Fig. 25
1.
Fold out the handlebar, lock it and lower the kickstand.
2.
Install the handlebar on the stem.
3.
Tighten the screws on both sides of the stem with the T-shaped Allen key.
4.
After assembly, press the power button to check for proper operation.
Charging the scooter
Fig. 26
1.
The electric scooter is fully charged when the LED light on the charger changes from red
(charging) to green (continuous charging).
2.
Open the rubber charging port cover.
3.
Connect the charger to the charging port.
4.
When charging is complete, re-attach the rubber cover.
How to ride
Warning: use helmet, elbow and knee pads. Please read the instructions carefully before using
the product. Do not modify the braking system. Check the instructions for further information.
•
Switch on the scooter and check the power indicator.
•
Place one foot on the deck and push off the ground with the other foot. When the
scooter starts to coast, place both feet on the platform and press the accelerator. Note:
Acceleration will start when the coasting speed exceeds 5 km/h.
•
The accelerator automatically switches off when the scooter is at a complete standstill.
To restart the scooter, repeat step 2.
•
Release the accelerator and the Kinetic Energy Recovery System (KERS) will
automatically start to brake slowly; press the brake lever to brake suddenly.
•
Tilt your body in the direction of steering when turning and slowly turn the handlebar
Control panel
•
On: one short press.
•
Off: a long press for 2 seconds.
•
Light: two short presses.
•
Drive mode: one short press.
1.
PEDESTRIAN mode: In this mode, the scooter can reach 6 km/h.
2.
COMFORT mode: In this mode, the scooter can reach 15 km/h.
3.
SPORT mode: In this mode, the scooter can reach 25 km/h.
•
Cruise control: three short presses.
•
No. of rolls: five short presses.
•
Gyroscope: hold down the brake lever and seven short presses.
64
ORIGINAL MANUAL TRANSLATION
Folded
Fig. 27
The scooter must be switched off before folding.
•
Hold the handlebar stem, turn it counterclockwise to open the safety hook and lift the
quick release lever.
•
Align the bell and hook and engage. When opened, unhook the bell lever from the
mudguard hook.
•
Unfold the handlebar stem, lock the quick release lever and rotate the handle bar
clockwise to close the safety hook.
Transportation
Hold the handlebar stem with one or both hands.
Adjusting the handlebar
Fig. 28
a.
Inner hexagon nut
b.
Hexagonal bolt
c.
Hexagon nut
Prolonged use of the scooter can cause the screws to loosen and the handlebar stem to
become unstable. If you notice that the handlebar stem wobbles when riding, follow the
steps below.
Tools
I: 8-10-mm wrench
II: 4 mm Allen key
Note: these tools must be in the user's possession.
Steps
1.
With the scooter folded, use tool I to loosen "c" (clockwise).
2.
Use tool I to loosen "b" (clockwise).
3.
Use tool II to adjust "a" (clockwise) to the proper position, and use tool I to tighten "b"
(counterclockwise).
4.
Lift the handlebar, close the quick release lever and turn the handlebar clockwise to
close the safety hook.
5.
Shake the handlebar stem to see if the problem has been resolved. If not, repeat steps 2
and 3. If resolved, continue to step 6.
6.
Fold the scooter again and use tool I to tighten "c" (counterclockwise).
*Step 6 is mandatory
ENGLISH
BONGO SERIE X65
65
Publicidad
