Hoshizaki IM-240DSME Manual De Instalación página 2

IMPORTANT
. In order to carry out safe and proper installation of the
product, please read this booklet carefully beforehand and
follow the instructions contained within.
2. On completion of the installation, start up the icemaker to
check for any abnormalities, and instruct the user on how
to use and maintain the icemaker in accordance with the
Instruction Manual.
3. This booklet should be handed over to the user after the
installation and be preserved by the user together with the
Instruction Manual for any further consultation that may be
necessary.
WARNING
The installation must be carried out by qualified personnel,
in accordance with current regulations, according to the
manufacturer's instructions.
1. UNPACKING
WARNING
Children should not be allowed in reach of the packaging
elements (plastic bags and expanded polystyrene) as they are
potential sources of danger.
CAUTION
Remove shipping carton, tape(s) and packing. If packing
material is left in the icemaker, it will not work properly.
Front Panel
Handle
Fig. 1
Note: . This icemaker needs a Storage Bin. Hoshizaki recommends
the following Ice Storage Bins:
B700SF ------------------ IM-240D/IM-480D
B800SF ------------------ IM-480D/IM-720D
B900SF ------------------ IM-480D/IM-720D
2. Remote air-cooled model requires HOSHIZAKI REMOTE
CONDENSER, Model URC-240C-E.
) After removing the packaging, make sure that the icemaker and the
Storage Bin are in good condition. If in doubt, please do not use
the equipment but apply to professionally qualified personnel. See
the instruction sheet attached to the Storage Bin for its unpacking
and installation guidelines.
2) Remove the icemaker panels to gain access to the accessory kit
and to assist easier installation.
[IM-240D]
a) Front Panel: Remove the screw(s). Lift up and pull toward you.
b) Top Panel: Remove the screw(s). Simply lift off.
c) Side Panel: Remove the screw(s). Slide forward slightly, and
then lift off.
d) Rear Panel: Does not require removal.
Top Panel
Power Cord
Bin Door
Storage Bin
(Optional)
Adjustable Legs
[IM-240X]
(No top panel)
Fig. 2
3) Remove the package of accessories, and check the contents:
a) Installation Kit
Inlet Hose
Outlet Hose
b) Scoop (Except IM-240X)
c) Ice Chute (IM-240X only)
d) Bracket (Except IM-240X)
e) Bolt 5 x 8 (Except IM-240X)
f) Bolt 8 x 6
g) Nut
h) Plastic Washer
i) Machine Screw 4 x 8 (IM-240X only)
j) Stainless Steel Washer (IM-240X only)
4) Remove the shipping tape holding the Bin Control Switch.
5) Remove the protective plastic film from the exterior. If the icemaker
is exposed to the sun or to heat, remove the film after the icemaker
cools.
2. LOCATION
. This icemaker is not intended for outdoor use. Normal
operating ambient temperature should be within °C to 40°
C. Normal operating water temperature should be within 5°
C to 35°C. Operation of the icemaker, for extended periods,
outside of these normal temperature ranges may affect
production capacity.
2. The icemaker should not be located next to ovens, grills or
other high heat producing equipment.
3. The location should provide a firm and level foundation for
the equipment.
4. Allow 5 cm clearance at rear, sides and top for proper air
circulation and ease of maintenance and/or service should
they be required. For air-cooled model only, allow 30 cm
clearance at the right side.
5. This appliance is not suitable for installation in an area where
a water jet could be used and where dripping is not allowed.
6. Do not place anything on top of the icemaker or in front of
the Louver.
7. This icemaker will not work at subfreezing temperatures. To
prevent damage to the water supply line, drain the icemaker
when air temperature is below zero.
3. INSTALLATION
* Incorrect installation can cause harm
to people, animals or things, for which
t h e m a n u f a c t u r e r c a n n o t b e h e l d
responsible.
) Lay the Storage Bin on its rear side
carefully to prevent damage. Secure
the four adjustable legs (bin accessory)
into the four tapped holes on the
underside of the Bin. See Fig. 3.
2) Position the Storage Bin in the selected
permanent position, and level it in
both the left-to-right and front-to-rear
directions. See Fig. 4.
3) Remove the icemaker panels. The
R e a r P a n e l i s n o t r e q u i r e d t o b e
removed for installation. See ".
UNPACKING".

ENGLISH




2
2
2
2
4
4
2
IMPORTANT
Fig. 3
Adjustable Leg
Fig. 4
Bottom
Adjustable Leg