Hoshizaki IM-240DSME Manual De Instalación página 4

5. ELECTRICAL CONNECTIONS
WARNING
THIS APPLIANCE MUST BE EARTHED
This icemaker requires an earth that meets the national
and local electrical code requirements. To prevent possible
severe electrical shock to individuals or extensive damage to
equipment, install a proper earth wire to the icemaker. Remove
the plug from the mains socket before any maintenance, repairs
or cleaning is undertaken.
* This icemaker must have a separate power supply or receptacle of
220 - 240V.
* Stacked icemakers should each have a separate receptacle, but
they must all be connected in parallel to the same single phase
supply or circuit with sufficient ampacity. In addition and to avoid
nuisance tripping, individual circuit breakers for each machine
should not be used.
* The main control box fuse is rated at 5A and should only be replaced
by a qualified service engineer.
* Usually an electrical permit and services of a licensed electrician are
required.
* If the supply cord and the plug should need to be replaced, it should
only be done by a qualified service engineer.
For the U.K. and the Republic of Ireland only
* The wires in the mains lead are coloured in accordance with the
following code:
Green & Yellow = Earth
Blue = Neutral
Brown = Live
As the colours of the wire in the mains lead of this appliance may
not correspond with the coloured markings identifying the terminals
in your plug, proceed as follows:
The wire which is coloured Green-and-Yellow must be connected
to the terminal in the plug which is marked with the letter E or by
the symbol or coloured Green or Green-and-Yellow. The wire
which is coloured Blue must be connected to the terminal which
is marked with the letter N or coloured Black. The wire which is
coloured Brown must be connected to the terminal which is marked
with the letter L or coloured Red.
* Should the socket outlets in the installation site not be suitable for
the plug supplied with your product, the plug must be removed (cut
off if it is moulded on plug) and an appropriate plug fitted.
If the non-rewirable plug has been cut from the power supply cord,
it must be disposed of. There should be no attempt to reuse it.
Inserting such a plug into a socket elsewhere presents a serious
risk of electrical shock.
* The non-rewirable plug must never be used without a fuse cover
being fitted.
The correct replacement for the detachable fuse cover is identifiable
from the manufacturer's reference number stamped on the plug.
Supply of replacement fuse covers can be obtained from Hoshizaki
Parts/Service Centres.
Fuses should be rated at 3A and approved to BS 362.
6. REMOTE CONDENSER UNIT
[a] UNPACKING
) Unpack and remove shipping carton, tape(s) and packing.
2) Remove the Top Panel.
Screw
3) Check that the refrigerant lines do not rub or touch lines or other
surfaces, and that the fan blade turns freely.
4) Recommended parts and materials listed below will be required.
Cord
7 AWG (.0 mm
Fan Motor wiring between the icemaker and the Condenser
Unit (L+N+ ).
Copper Tubing
Phosphorus deoxidized copper tubing. Two tubings of
the same size will be required for refrigerant lines. Mark
them for a distinction between the gas line and liquid line to
prevent misconnection.
9.52 (OD) x 7.93 (ID) - Gas
9.52 (OD) x 7.93 (ID) - Liquid
Pipe Insulation (for gas and liquid pipes)
To withstand temperatures up to 20°C.
Bolt
Four M8 Hexagon Bolts for securing the Condenser Unit.
5) Do not remove the Unit Covers before finishing installation, to
prevent damage to the air-cooled Condenser.
[b] LOCATION
The Condenser is intended for outdoor use and must be positioned in
a permanent well ventilated site under the following guidelines:
* Select a firm and flat site.
* Should not be exposed to harsh or adverse weather conditions.
* Preferably a dry and well ventilated area with 60 cm clearance on
both front and rear for ease of maintenance and service should they
be required.
Min. 60 cm clearance
Air
* N o r m a l c o n d e n s e r a m b i e n t t e m p e r a t u r e : +  ° C t o + 4 0 ° C .
Temperatures not within this operating range may affect the
production capacity of the icemaker.
* When the Condenser Unit is installed on a roof, a 50 cm height
base is recommended to prevent heat reflection and to avoid the
possibility of the unit standing in water.
* The maximum line length is 0 m. For information on longer line
installations, call Hoshizaki Care +44 (0) 223242254.
* The Condenser should not be installed more than 6 m above the
height of the icemaker or more than 2 m below it.
Note: If the recommended guidelines of the installation are exceeded,
the icemaker performance may be reduced.
3
ENGLISH
Top Panel
Fig. 10
Unit Cover
2
) three-wire cord will be required for the
Air
Fig. 11