Publicidad
Idiomas disponibles
Idiomas disponibles
CAUTION
An incorrectly installed saw chain leads to uncontrolled
cutting behaviour by the product!
When fitting the saw chain, observe the prescribed run-
ning direction!
• Place the product on a level, even surface.
8.1
Fit the guide bar (8) and saw chain
(7) (Fig. 2)
Note:
To fit the saw chain, it may be necessary to tilt the chain-
saw to the side.
1. Turn the chain tensioning wheel (9) anti-clockwise, so
that the chain cover (10) is removed.
2. Lay out the saw chain (7) in a loop so that the cutting
edges are aligned clockwise. To align the saw chain
(7), follow the symbols (arrows) on the saw chain (7)
or above the guide pin (19).
3. Place the saw chain (7) in the groove of the guide bar
(8).
4. Insert the guide bar (8) on the guide pin (19) and the
stud bolt (18). Both guide pins (19) and the stud bolt
(18) must be in the elongated hole on the guide bar
(8).
5. Guide the saw chain (7) around the chain wheel (17)
and check the alignment of the saw chain (7).
6. Fit the chain cover (10) back on.
Make sure that the chain cover (10) sits in the groove
on the housing.
7. Tighten the tensioning wheel (9) clockwise hand-tight.
8. Recheck the seating of the saw chain (7) and tension
the saw chain (7) as described under 8.2.
8.2
Tensioning the saw chain (7) (Fig.
1)
WARNING
Risk of injury from the saw chain jumping off!
An insufficiently tensioned saw chain can come off
during operation and cause injuries.
–
Check the saw chain tension frequently.
–
The chain tension is too low if the drive links come
out of the groove on the underside of the guide rail.
–
Adjust the tension of the saw chain properly if the
saw chain tension is too low.
1. Turn the chain tensioning wheel (9) clockwise to ten-
sion the saw chain (7).
The saw chain (7) must not sag, although it should be
possible to pull it 1-2 millimetres away from the guide
bar (8) in the centre of the guide bar.
2. Turn the saw chain (7) by hand, to check it runs freely.
It must glide freely in the guide bar (8).
The chain tension and chain lubrication have a consider-
able influence on the service life of the saw chain.
The saw chain is correctly tensioned when it does not sag
on the guide bar and can be pulled all the way round with
a gloved hand. When pulling on the saw chain with 9 N
(approx. 1 kg) tractive force, the saw chain and guide bar
must not be more than 2 mm apart.
Note:
• The tension of a new chain must be checked after a
few minutes in operation, and adjusted if necessary.
• The tensioning of the saw chain should be carried out
in a clean place free from sawdust and the like.
• Correct tensioning of the saw chain is for the safety of
the user and reduces or prevents wear and chain
damage.
• We recommend that the user check the chain tension
before starting work for the first time. The saw chain is
correctly tensioned when it does not sag on the under-
side of the guide bar and can be pulled all the way
round with a gloved hand.
• If the saw chain sags or the spring tensioner is defec-
tive, contact a specialist workshop.
ATTENTION
When working with the saw, the saw chain heats up
and expands slightly as a result. This "stretching" is to
be expected especially with new saw chains.
8.3
Topping up saw chain oil (Fig. 3)
DANGER
Always switch off the product and let the motor cool
down before filling with oil. There is a risk of fire if oil
overflows.
ATTENTION
Product damage!
If the product is operated without oil or with too little oil
or with used oil, this can lead to product damage.
–
Fill with oil before starting the machine. The product
is delivered without oil.
–
Do not use used oil!
–
Check the oil level every time you change the bat-
tery.
ATTENTION
Environmental damage!
Spilled oil can pollute the environment permanently.
The liquid is highly toxic and can quickly lead to water
pollution.
–
Fill/empty oil only on level, paved surfaces.
–
Use a filling nozzle or funnel.
–
Collect drained oil in a suitable container.
–
Wipe up spilled oil carefully immediately and dis-
pose of the cloth according to local regulations.
–
Dispose of oil as per local regulations.
www.scheppach.com
GB | 29
Publicidad
