Publicidad
Idiomas disponibles
Idiomas disponibles
The saw chain will be lubricated automatically while the
product is running. To lubricate the saw chain sufficiently,
there must always be enough saw chain oil in the oil tank.
Check the amount of oil remaining in the oil tank at regu-
lar intervals.
Note:
• The cover is equipped with an anti-loss device.
• Only add environmentally friendly, good quality chain
lubricating oil (per RAL-UZ 48) to the chain saw.
• Ensure that the cover of the oil tank is in place and
closed before switching on the product.
1. Open the oil tank (14). To do this, unscrew the oil tank
cap (14) anti-clockwise.
2. To prevent oil from leaking, use a funnel*.
3. Carefully add the chain lubricating oil until it reaches
the top mark on the oil level indicator (13). Oil tank ca-
pacity: max. 260 ml.
4. Screw down the cover of the oil tank (14) clockwise to
close the oil tank (14).
5. Wipe up any spilled oil carefully immediately and dis-
pose of the cloth according to local regulations.
6. To check the product lubrication, hold the chainsaw
with the saw chain over a sheet of paper and give it
full throttle for a few seconds. You can see on the pa-
per whether the chain lubrication is working.
* = not included in the scope of delivery!
8.4
Inserting/removing the batteries
(20) in the battery mounts (4) (Fig.
4)
CAUTION
Danger of injury!
Do not insert the battery until the battery-powered tool
is ready for use.
Inserting the battery
1. Slide the batteries (20) into the battery mounts (4).
The batteries (20) click into place audibly.
Removing the battery
1. Press the unlock button (21) of the battery (4) and re-
move the batteries (20) from the battery mounts (4).
8.4.1
Charge level indicator (11) (Fig. 4)
The charge status indicator (11) indicates the charge sta-
tus of the battery (20).
The charge status of the battery is indicated by the corre-
sponding LED light lighting up.
1. Press the button on the charge level indicator (11) to
check the charge level.
3 LEDs illuminate
2 LEDs illuminate
1 LED illuminates
8.5
Safety devices (Fig. 1)
• Rear handle (1) with hand guard
– Protects the hands from branches and twigs and if
the chain jumps off.
30 | GB
Battery fully charged
Battery partially charged
Battery must be charged
www.scheppach.com
• On/off switch (2) with chain instant stop
– Switches the product off immediately if the on/off
switch is released.
• Chain brake/front hand guard (6)
– Safety devices that stop the saw chain immediate-
ly in the event of kick-back.
– The lever can also be manually actuated.
– Protects the left operator's left hand if it slips off
the front handle.
• Saw chain (7) with low kick-back
– Helps you to intercept kick-backs with specially
developed safety devices.
• Switch lock (12)
– To switch on the product, the switch lock must be
unlocked.
• Claw stop (15)
– Reinforces stability when vertical cuts are per-
formed and makes sawing easier.
9
Operation
The cordless chain saw is equipped with a quick-tension-
ing system for the chain. The saw chain runs around the
edge of the guide bar (guide rail). An automatic oil system
ensures continuous chain lubrication. To protect the us-
ers, the product has various safety devices (see8.5).
Please refer to the following descriptions for the function
of the controls.
ATTENTION
Always make sure the product is fully assembled
before commissioning!
ATTENTION
Make sure that the ambient temperature does not ex-
ceed 50°C and does not fall below -20°C during work.
ATTENTION
The product is part of the 20V IXES series and may on-
ly be operated with batteries of this series. Batteries
may only be charged with battery chargers of this se-
ries. Observe the manufacturer's instructions.
DANGER
Danger of injury!
If the product is jammed, do not try to pull the product
out by using force.
–
Switch off the engine.
–
Use a lever arm or wedge to get the product free.
9.1
Chain brake (Fig. 1, 5)
WARNING
The chain brake must be checked before
each use.
The chain brake brakes the saw chain immediately in
the event of kick-back.
Publicidad
