Publicidad
Idiomas disponibles
Idiomas disponibles
Even when this tool is used as prescribed it is not possible to eliminate
all residual risk factors. If you are in any doubt as to safe use of this tool,
do not use it
Product Familiarisation
1. Blade Height Winder
2. Bevel Angle Adjuster
3. Blade Height Lock
4. Bevel Angle Locking Lever
5. Mains Plug
6. Bevel Angle Gauge
7. Hand-Slot Cover Screw Holes
8. Saw Blade
9. Module Locator Tabs
10. Front Blade Guard Cover
11. Blade Guard
12. Blade Guard Dust Port
13. Riving Knife
14. Anti-Kickback Pawl
15. Dust Extraction Port
16. Lateral Alignment Wheel
17. Module Levelling Bobbin
18. Motor Housing
19. Circuit Breaker Reset Button
20. Kerf Plate Lock
21. Anti-Kickback Slot
22. Blade Guard Slots
23. Anti-Kickback Locating Lever
24. Anti-Kickback Locking Pin Lever
25. Blade Guard Locking Lever
26. Blade Guard Locating Front Pin
27. Blade Guard Locating Rear Pin
28. Blade Height Winder Gear Access Cover
29. Kerf Plate
30. Sacrificial Plate
31. Kerf Plate Levelling Screw Hole
32. Module Levelling Screw
33. Kerf Plate Access Hole
34. Module Table Surface
35. Hand Slot
36. Module Levelling Bobbin Screw
37. Riving Knife Locking Lever
38. Kerf Plate Levelling Screw
39. Blade Flange
40. Blade Washer
EN
41. Blade Securing Nut
42. Arbor
43. Mounting Tab
44. Fixing Screw
45. Push Stick
46. Multi-Tool 1
47. Multi-Tool 2
26
48. Protractor Gauge
49. Bench Locking Knob
50. Adjustable Front Fence
51. Supporting Bracket
52. 45° Angle Fence
53. Angle Slot
54. Graduation Scale
55. Angle Viewfinder
56. Bench Rail
57. Angle Adjustment Knob
58. Rip Fence Side Arm
59. Rip Fence
60. Rip Fence Back Bar
61. Rip Fence Frame Fixing Bolts
62. Rip Fence Clamp
63. Rip Fence Clamp Lever
64. Rip Fence Clamp Tension Screws
65. Rip Fence Height Adjustment Screw
66. Rip Fence Scale Indicator
67. Rip Fence Side Arm Clamp
68. Rip Fence Roller
69. Rip Fence Roller Lock Nut
70. Rip Fence Clamp Mounting Holes
71. Rip Fence Clamp Mounting Bolts
72. Rip Fence Horizontal Adjustment Screw
73. Hand-Slot Cover
74. Riving Knife Alignment Screws
75. 45° Trimming Screw
76. 0° Trimming Screw
77. Dust Extraction Port Adaptor
Intended Use
An effective saw table capable of mitre, bevel and cross cutting.
Includes Protractor Gauge and Rip Fence. Suitable for cutting wood and
wood-like materials only. For use with the Triton Workcentre TWX7 and
accessories.
The tool must ONLY be used for its intended purpose. Any use other
than those mentioned in this manual will be considered a case of
misuse. The operator, and not the manufacturer, shall be liable for any
damage or injury resulting from such cases of misuse. The manufacturer
shall not be liable for any modifications made to the tool, nor for any
damage resulting from such modifications.
Note: Not intended for commercial use.
Unpacking Your Tool
• Carefully unpack and inspect your tool. Fully familiarise yourself with
all its features
and functions
• Ensure that all parts of the tool are present and in good condition. If
any parts are missing or damaged, have such parts replaced before
attempting to use this tool
IMPORTANT: Read these instructions in combination with the
instructions supplied with your Triton Workcentre.
Publicidad
