Stiga SRSW01 Manual De Instrucciones página 11

Swimming pool,
Overflow pond,
Unprotected public
road
Swiming pool or
road at the end of
a descent
TYPES OF OBSTACLE DELIMITATIONS
X-PASSAGE BETWEEN TWO DIFFERENT SECTIONS OF
PERIMETER CABLE
TYPE
SRSW01 SRBW01
X>= 70 cm X>= 90 cm
(Fig. 4) (Fig. 4)
X< 70 cm X< 90 cm
(Fig. 5) (Fig. 5)
TRANSITIONS BETWEEN DIFFERENT AREAS OF THE
GARDEN
CORRIDOR WIDTH Z
TYPE
SRSW01 SRBW01
Z>= 70cm Z>= 90cm
(Fig. 6) (Fig. 6)
Z< 70cm Z< 90cm
(Fig. 6) (Fig. 6)
CAUTION:
The operating area and in general the areas
where
the robot lawn mower can navigate must be
delimited by a non-crossable fence.
Ensure that the fence is suitably enclosed or
monitor the robot lawn mower while
operating.
2.3. COMPONENTS INSTALLATION
ELECTRICAL HAZARD:
Only use the battery charger and power supply
provided by the manufacturer. Improper use
may cause electric shock and\or overheating.
CAUTION:
Danger of cutting hands.
Use protective gloves to avoid cutting your
hands.
90 cm 100 cm
150 cm 150 cm
The obstacle can be delimited
by overlapping the outward and
return cable sections without
crossing them.
The obstacle can be delimited
by spacing the two sections of
the outward and return cable
by at least Y= 30 cm. If the
obstacle is sufficiently robust it
can be left unprotected.
The area (Fig. 6 A) can be
reached by the robot lawn
mower.
The area (Fig. 6 A) cannot
be reached by the robot lawn
mower and is considered a
"Closed Area".
EN
CAUTION:
Danger of dust in the eyes.
Use safety glasses to avoid the danger of
dust in the eyes.
ELECTRICAL HAZARD:
Connect the power supply only at the end of
all the installation operations. If necessary
during the installation, turn off the general
power supply.
2.3.1. INSTALLATION OF THE PERIMETER CABLE
POSITIONING WITH PEGS
1. Run the perimeter cable starting from the installation area
of the charging base.
2. Run the cable along the entire length of the route and secure
it using the pegs provided (Fig. 7.B) approximately 100 cm
apart, and complying with the installation requirements
provided (See par. 2.2).
3. Leave 2 m of cable or more to subsequently cut it to size
in the final phase of connection.
4. When making a bend, position the cable in such a way
to ensure that the bending radius is approximately 20
cm (Fig. 7.A).
MAXIMUM
LENGTH OF STIGA CABLES COMPATIBLE WITH THE
PERIMETER
CABLE
Code 1127-0000-01
Code 1127-0001-01
< 400m
Code 1127-0002-01
Code 1127-0003-01
Code 1127-0002-01
>= 400m up to
max. 1000m
Code 1127-0003-01
WARNING:
Make sure that the cable is in contact with
the ground along its path to prevent the robot
lawn mower from damaging it.
NOTE: The perimeter cable used for installation must
be at least 40 m. long. If the cable is shorter, it will be
necessary to install the resistor code 122063053/0. Refer
to the complete instruction Manual.
2.3.2. CHARGING BASE INSTALLATION
Install the charging base aligned with the perimeter cable
so that the robot will be able to access it by navigating the
perimeter cable clockwise.
1. Check the installation requirements as indicated in par. 2.2.
2. If necessary, prepare the ground so that the surface of
the charging base is at the same level as the lawn, the
ground must be perfectly flat and compact in order to
avoid deformation of the surface of the charging base.
4
INSTALLATION
150 m Reel,
Ø 2.7 mm
300 m Reel,
Ø 2.7 mm
500 m Reel,
Ø 3.4 mm
1000 m Reel,
Ø 3.4 mm
500 m Reel,
Ø 3.4 mm
1000 m Reel,
Ø 3.4 mm