Publicidad
Idiomas disponibles
Idiomas disponibles
Operation
Preparation
f Check that the contents are complete.
f Check all the parts for possible transport damage.
Safety
Caution! Damage due to incorrect power supply.
f Only operate the appliance with the voltage stated on
the nameplate.
Caution! Damage due to deep discharge of battery
f Always switch the appliance off with the on/off switch
after use (Fig. 3ⓑ).
f Always switch the appliance off with the on/off switch
when charging the battery (Fig. 3ⓑ).
Charging the battery
Before the appliance is used for the first time, it should be
charged for approx. 2 hours!
1. Switch off the appliance using the on/off switch (Fig. 3ⓑ).
2. Connect the appliance plug on the plug-in transformer to the appli-
ance socket (Fig. 2ⓐ).
Battery overcharging is prevented thanks to intelligent
charge management.
3. Connect the plug-in transformer to the mains socket (Fig. 2ⓑ).
During charging, the charging indicator flashes at evenly
spaced intervals. When the battery is fully charged, the
charging indicator flashes at a different rate (10 on / 1 off).
Battery operation
1. Switch on the appliance using the on/off switch and switch off after
use (Fig. 3ⓐ/ⓑ).
Mains operation
Caution! Damage due to use of the appliance with the
plug-in transformer permanently plugged in (mains
operation)
The appliance is not designed to be used with the plug-in
transformer permanently plugged in (mains operation). The
plug-in transformer connecting cable is not designed for
mechanical stress in continuous operation.
f Mains operation is only recommended for short periods
of use, in the event of an empty battery.
1. Connect the appliance plug on the plug-in transformer to the appli-
ance socket (Fig. 2ⓐ).
2. Connect the plug-in transformer to the mains socket (Fig. 2ⓑ).
3. Switch on the appliance using the on/off switch and switch off after
use (Fig. 3ⓐ/ⓑ).
Operation
Cutting with attachment comb
The appliance can also be operated with an attachment comb.
f The attachment comb has 5 detent positions for adjusting the cut-
ting length.
f The further the attachment comb is pushed onto the blade set, the
shorter the cutting length.
The cutting length can be adjusted from 3 mm (Fig. 5ⓐ) to
6 mm (Fig. 5ⓑ).
Attaching/removing the attachment comb
1. Slide the attachment comb onto the blade set (Fig. 4ⓐ) in the
direction of the arrow until it locks in place.
2. The attachment comb can be removed by pushing it in the direc-
tion of the arrow (Fig. 4ⓑ).
Maintenance
Warning! Injuries and material damage due to incorrect
handling.
f Switch off the appliance before cleaning it or performing
any maintenance and disconnect it from the mains.
Cleaning and care
Danger! Electric shock due to penetration of liquid.
f Do not immerse the appliance in water!
f Do not allow any liquid to get inside the appliance.
Caution! Danger from aggressive chemicals.
Aggressive chemicals could damage the appliance and
accessories.
f Never use solvents or scouring agents.
f Only use cleaning agents and blade set oil recom-
mended by the manufacturer.
Accessories and spare parts are available from your dealer or
our service centre.
f Remove the attachment comb (Fig. 4ⓑ) and lift the blade set out
of the housing (Fig. 6ⓐ). Use the cleaning brush to remove any cut
hairs from the housing opening and from the blade set (Fig. 7).
f Only wipe the appliance with a soft, slightly damp cloth.
f Oil the blade set with blade set oil (Fig. 8).
f For a good and long-lasting cutting performance, it is
important to oil the blade set frequently.
f If the cutting performance deteriorates after long use
despite regular cleaning and oiling, the blade set should
be replaced.
E N G L I S H
de
en
fr
it
es
pt
nl
da
sv
no
fi
tr
pl
cs
sk
hr
hu
sl
ro
bg
ru
uk
et
lv
lt
el
9
ar
Publicidad
