Caution; Important - Yamaha DSP-A1 Manual De Instrucciones

CAUTION : READ THIS BEFORE OPERATING YOUR UNIT.
1.
To assure the finest performance, please read this manual
carefully. Keep it in a safe place for future reference.
2.
Install this unit in a cool, dry, clean place – away from
windows, heat sources, sources of excessive vibration,
dust, moisture and cold. Avoid sources of humming
(transformers, motors). To prevent fire or electrical shock,
do not expose the unit to rain or water.
3.
Never open the cabinet. If something drops into the set,
contact your dealer.
4.
Do not use force on switches, controls or connection wires.
When moving the unit, first disconnect the power plug and
the wires connected to other equipment. Never pull the
wires themselves.
5.
The openings on the cabinet assure proper ventilation of
the unit. If these openings are obstructed, the temperature
inside the cabinet will rise rapidly. Therefore, avoid placing
objects against these openings, and install the unit in well-
ventilated condition. Make sure to allow a space of at least
10 cm behind, 10 cm on the both sides and 30 cm above
the top panel of the unit. Otherwise it may not only damage
the unit, but also cause fire.
6.
The voltage to be used must be the same as that specified
on this unit. Using this unit with a higher voltage than that
which is specified is dangerous and may result in a fire or
other type of accident causing damage. YAMAHA will not
be held responsible for any damage resulting from use of
this unit with a voltage other than that which is specified.
7.
Digital signals generated by this unit may interfere with
other equipment such as tuners, receivers or TVs. Move
this unit farther away from such equipment if interference
is observed.
8.
Always set the VOLUME control to "–
the audio source play. Increase the volume gradually to an
appropriate level after playback has been started.
9.
Do not attempt to clean the unit with chemical solvents;
this might damage the finish. Use a clean, dry cloth.
10.
Be sure to read the "TROUBLESHOOTING" section
regarding common operating errors before concluding that
the unit is faulty.
11.
When not planning to use this unit for long periods of time
(ie., vacation, etc.), disconnect the AC power plug from the
wall outlet.
12.
To prevent lightning damage, disconnect the AC power
plug and antenna cable when there is an electrical storm.
13.
Grounding or polarization – Precautions should be taken
so that the grounding or polarization of an appliance is not
defeated.
14.
Do not connect an audio equipment to the AC outlet on the
rear panel if the equipment requires more power than the
outlet is rated to provide.
15.
Voltage Selector (China and General Models only)
The voltage selector on the rear panel of this unit must
be set for your local main voltage BEFORE plugging
into the AC main supply.
Voltages are 110/120/220/240 V AC, 50/60 Hz.
This unit is not disconnected from the AC power source as
long as it is connected to the wall outlet, even if this unit
itself is turned off. This state is called the standby mode.
In this state, this unit is designed to consume a very small
quantity of power.
∞
" before starting

IMPORTANT

Please record the serial number of this unit in the space
below.
Model:
Serial No.:
The serial number is located on the rear of the unit.
Retain this Owner's Manual in a safe place for future
reference.
WARNING
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK,
DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE.
FREQUENCY STEP switch (China and General Models
only)
Because the interstation frequency spacing differs in
different areas, set the FREQUENCY STEP switch (located
at the rear) according to the frequency spacing in your area.
Before setting this switch, disconnect the AC power plug of
this unit from the AC outlet.
FOR CANADIAN CUSTOMERS
TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE
OF PLUG TO WIDE SLOT AND FULLY INSERT.
THIS CLASS B DIGITAL APPARATUS MEETS ALL
REQUIREMENTS OF THE CANADIAN INTERFERENCE-
CAUSING EQUIPMENT REGULATIONS.
WARNING
Do not change the IMPEDANCE SELECTOR switch
setting while the power to this unit is on, otherwise this
unit may be damaged.
IF THIS UNIT FAILS TO TURN ON WHEN THE
STANDBY/ON SWITCH IS PRESSED;
The IMPEDANCE SELECTOR switch may not be set to
either end closely. If so, set the switch to either end closely.
IMPEDANCE SELECTOR
+
A B
A OR B
VOLTAGE SELECTOR
FRONT REAR
(SURROUND)
(General model)
IMPEDANCE SELECTOR
SET BEFORE POWER ON
MAIN : 4ΩMIN. /SPEAKER
CENTER A B : 4ΩMIN. /SPEAKER
A OR B : 4ΩMIN. /SPEAKER
REAR : 4ΩMIN. /SPEAKER
FRONT EFFECT : 6ΩMIN. /SPEAKER
MAIN : 8ΩMIN. /SPEAKER
CENTER A B : 4ΩMIN. /SPEAKER
A OR B : 8ΩMIN. /SPEAKER
REAR : 8ΩMIN. /SPEAKER
FRONT EFFECT : 8ΩMIN. /SPEAKER
AC OUTLETS
SWITCHED UNSWITCHED
I00W MAX. TOTAL 200W MAX.
3