Installation; Connect The Inlet Hoses; Instructions - Maytag EPIC z Manual De Uso Y Cuidado

Ocultar thumbs Ver también para EPIC z:
Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

_!!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_![[i_i_!iiii_!iiii_!iiii_!iiii_!iiii_!iiii_!iiii_!iiii_!iiii_!iiii_!iiii_!iiii_!iiii_!iiii_!iiii_!iiii_!iiii_!iiii_!iiii_!iiii_!iiii_!iiii_!iiii_!iiii_!iiii_!iiii_!iiii_!iiii_!iiii_!iiii_!iiii_!iiii_!iiii_!iiii_!iiii_!iiii_i_!iii!!_!_!_!_!_i!i!{i!_i!_!ji!!_!_!_!_!!i!i!_i_jii!_!_!_!_!_!!!!i[ii_._!ii!ii!!_jjii!_!iiiiji!!_!_!_!_!_!!i!i_}_!_!_!_!_l!l!!!i!!!_
4_,
i!i[ii_!!!!_iiiiii}ii}_!!i_i_}_i_iii_!ii_!!!_iiiiii}_!iji_!_!i_ii!ii!_!_!_!_i!_ii_1!_!_!_i!i!ii!!_iii!i)ii_:i_!_i[ii_i_!!_
_!_i!_!_!_!!i!i!ii!!_ii!!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_
¸
INSTALLATION
INSTRUCTIONS
Excessive
Weight
Hazard
Use two or more people
to move and install
washer.
Failure
to do so can result
in back or other
injury.
IMPORTANT:
Position
the washer
so that the rear of the washer
is within
approximately
3 ft
(90 cm) of its final location.
There are 4 blue bolts in the rear panel of the washer
that support
the suspension
system
during
transportation.
These bolts also retain the power cord
inside the washer
until the bolts
are removed.
1.
Using a 13 mm wrench,
loosen each of the bolts.
2.
Once the bolt is loose, move it to the center of the hole and completely
pull out the bolt,
including
the plastic spacer covering
the bolt.
Insert new flat washers
(supplied)
into each end of the inlet hoses. Firmly seat the washers
in
the couplings.
A
B
A. C_;upling
B. Washer
Connect the inlet hosesto the water faucets
Make sure the washer
drum is empty.
1.
Attach
a hose to the hot water faucet.
Screw on coupling
by hand until it is seated on the
washen
2.
Attach
a hose to the cold water faucet.
Screw on coupling
by hand until it is seated on the
washen
3.
Using pliers, tighten
the couplings
with an additional
two-thirds
turn.
NOTE: Do not overtighten
or use tape or sealants on the valve. [Damage to the valves can
result.
3.
Once all 4 bolts are removed,
discard
the bolts and spacers. Then pull the power
cord
through
the opening
of the rear panel and close the hole with the attached
cap.
4.
Close the bolt holes with
the 4 transport
bolt hole plugs.
NOTE: If the washer
is to be transported
at a later date, call your local service
center. [b avoid
suspension
and structural
damage,
your machine
must be properly
set up for relocation
by a
certified
technician.
10

Publicidad

Tabla de contenido

Solución de problemas

loading

Tabla de contenido