Removing The Fabric Cover - Babyauto UNIT FIX 0123 Manual De Uso

7. Pull the iSoFiX adjuster and push the safety seat towards the back using
a firm, constant pressure on both sides until it rests firmly against the
vehicle seat (fig. 6.4). if necessary, adjust the reclining of the vehicle´s
seat backrest to ensure that the child seat rests correctly.
8. Take the Top Tether and press the Top Tether adjuster to stretch the strap.
9. Hook the safety clasp to the Top Tether anchor point recommended in
your vehicle instruction manual (fig. 6.5).
IMPORTANT! Make sure not to use the luggage clip instead of
the Top Tether anchor clip. Look for this symbol in your vehicle:
10. To tighten the Top Tether, take up any slack by pulling the free end of the belt
through the Top Tether adjuster (fig. 6.5). The Top Tether will be correctly
tightened when the green tension indicator extends 1 mm (fig. 6.7).
Uninstalling the Isofix arms
1. To release the iSoFiX arms, pull the button on the anchors to unlock
them until the indicator turns from green to red color. This will
release the child seat (fig. 6.8).
7. removing the harness and safety bUcKle
7.1 removing the 5 point harness and the safety buckle
1. Loosen the harness straps by pulling them gently while pressing the
harness adjustment button
2. Loosen the harness straps from the back of the seat, freeing them
from the harness connector (N). Repeat the operation with the
shoulder straps connector
3. Pull the harness straps from the front to free them from the seat back.
(fig. 7.3).
4. Take off the safety buckle, passing the retention plate through the
seat base slots (fig. 7.4).

7.2 removing the fabric cover

1. Put the headrest in the higher position.
2. Take off the headrest fabric cover.
24
(J) (fig. 7.1)
(P) (fig. 7.2).
3. Take off the fabric cover from the car seat.
8. installing the child seat. groUP 2/3 (isoclicK+toP tether)
Before installing the seat for Group 2, the seat harnesses (e), harness
( d) (f)
protectors and buckle must be removed. Please, for this, follow
chapter 8, section 1.
1. Ensure the seat is not in a reclined position (the indicator should be in
position 1) and is ready to install in forward position (Group 2/3) (fig.
6.1. Pull the lever (H) forward and adjust the angle of recline to position
without releasing the lever. Release the lever when the seat is in the
desired position.
2. Place the child safety seat in the back seat of the vehicle facing in the
direction of travel.
3. Follow the steps described in chapter
installation.
NOTICE / ONLY GROUP 2: For this group, it is possible to install the car
seat using only the 3-point belt of the vehicle without using the isoclick
connectors and the top tether anchor. To do this, follow steps 1 and 2 of
this chapter and then proceed to place the child as described in Chapter 9.
9. Placing the child in the seat. groUP 2/3
1. According to the child's height the headrest can be adjusted up or down.
Place your hand on the headrest height regulator
pulling the seat down with the other hand so it does not move (8.2).
2. Place the child in the seat.
3. Pass the vehicle seat belt and buckle the vehicle seat belt until you
hear a click (fig. 8.5 and 8.6).
4. Make sure the abdominal belt section passes over the abdominal belt
guides (K) (fig. 8.5 and 8.6)
5. Pass the diagonal part of the belt through the diagonal belt guide
the headrest until it is fully extended and not twisted (fig. 8.7).
6. Take up the slack by pulling the diagonal belt section until it is as
tight-fitting as possible.
6.1 to complete the car seat
(a) and pull while
(c) on
25