Optional Equipment - Convotherm OSC 6.10 Manual De Instalación

English
5.

Optional Equipment

5.1 Disappearing Door
n Installation / positioning
Note the minimum distance to neighboring units /
walls: see Chapter 1.4 and 1.5
n Guiding stirrup (if not installed yet)
Pic. 17
After positioning units with the disappearing door,
the guiding stirrup must be assembled on top of the
unit with the enclosed screws.
n Dimensional drawings for disappearing door see
Chapter 5.6 and at the end of the handbook.
5.2 Stacking Kit (only for 6.10 and 10.10)
n The stacking kit is used to stack two CONVOTHERM
OSC's or CONVOTHERM OSP's one upon another.
Never stack a 10.10 model on top!
n Special tools: drill, drill bit for steel Ø 4 and 7 mm and
M5 thread tap.
n Upon delivery:
Pos. Description
1 Top foot stand
2 Lower stand
3 Cover left
4 Cover right
5 Cover front
6 Steam panel
7 Elbow 42 i-i
8 Flat siphon
9 Pipe
10 Steam exhaust pipe
11 Screw
12 Washer
13 Pipe clip
14 Silicone
15 M4 screw
16 Washer
17 M5 screw
18 Washer
Instructions for installing the stacking kit:
n Stand the lower unit on the lower stand and align unit
Pic. 18
so that it is level
n Mount the top stand on the unit
Pic. 19
Take care that the top foot stand does not collide
with the hinge bracket of the lower unit.
– Drill holes (two).
– Place the stand on top of the lower unit.
– Fix at the rear using two M5 screws with washers
Part No.: 7006300 / 06/2003 Edition
n Stand the lower unit upon the top foot stand and align
n Mount the cover
–
the bottom of the unit and the table surface to ~202mm (use a
water level - units must be adjusted level from right to left and
from front to back).
–
must be fastened to the front panel by overlapping the angled
parts and fixing with two M4 screws. Install the steam panel at
the same time. Hang the steam panel by inserting the catches
into the slots in the front panel, clap shut and fasten all three
pieces (left panel, front panel and steam panel) with the M4
screws.
–
of the cover is slotted into the gap at the rear of the stand.
–
washers.
n Mount the steam exhaust pipe
–
–
–
silicone and clip in.
Part-No. pcs
3406552 1
3406556 1
3408346 1
5.3 Marine Version
3408347 1
n Set up on floor or table
3408348 1
3409276 1
6006032 2
n Assembling on a stand marine version
3007080 2
–
6006054 1
using a water level and adjust the height of the feet accordingly.
3406594 1
–
8003043 1
screw tightly and screw the angle into the floor.
8006040 1
–
6006084 1 remove them.
–
7004020 1
underside.
8001024 4
–
8005021 4
–
8001031 2
(use water level).
8005030 2
–
underneath using the enclosed M10 screws with washer and
spring washer.
Page 20 / 71
unit so that it is level.
Using the height-adjustable feet, adjust the distance between
The cover is made up of 4 parts. The side panels of the cover
Place the cover around the top foot stand. Make sure the rear
Fix the cover in place at the front using two M4 screws and
Drill a hole in the back of the unit.
Mount the pipe clip.
Mount both angles, pipe piece and steam exhaust pipe with
Neither steam exhaust support should be extended,
tapered or clogged.
Fasten the unit according to the condition of the
installation surface.
Ensure that the stand marine version is horizontally level
Align fastening angle on table base over the long holes, re-
Disassemble unit feet with flange plates for fastening and
Assemble enclosed unit feet with M10 thread on the feet
Place unit on stand and align over the holes (Ø13 mm).
Using the height adjustable feet, align unit to level position
Screw the stand's square pipe to the unit feet from
Pic. 20
Pic. 21
Pic. 22
Pic. 23/24