Specifications; Lcd Panel; Input/Output Terminals - JVC DT-V21G11 Manual De Instrucciones

Specifications

General
Model name
Type
Screen size
Aspect ratio
Compliant video signal format
Format
Audio output
Operation environment
Power requirements
Rated current
External dimensions (excluding protruding
parts)
Mass
Accessories

LCD panel

Type
Effective screen size
Number of pixels displayed
Number of colors displayed
Contrast ratio (TYP.)

Input/output terminals

DVI-D (HDCP)
E. AUDIO 3G SDI/HD SDI/SD SDI (IN 1)
E. AUDIO 3G SDI/HD SDI/SD SDI (IN 2)
E. AUDIO 3G SDI/HD SDI/SD SDI
(SWITCHED OUT)
VIDEO
COMPO. (Y, P /B-Y, P /R-Y)
B R
AUDIO (IN)
AUDIO (MONITOR OUT)
REMOTE (MAKE/TRIGGER)
REMOTE (RS-485)
REMOTE (RS-232C)
28
DT-V21G11
MULTI FORMAT LCD MONITOR
Type 21 wide format
16:9
☞ "Available signals" on page 29
3G SDI :
DUAL LINK HD SDI :
HD SDI :
SD SDI :
EMBEDDED AUDIO :
Internal speaker: 1.0 W + 1.0 W
Operating temperature: 5°C – 35°C
Operating humidity: 20% – 80% (non-condensing)
(Slightly variable depending on ambient conditions for installation.)
AC 120 V/AC 220 – 240 V, 50 Hz/60 Hz
0.6 A (AC 120 V)
0.4 A (AC 220 – 240 V)
with the stand
Width: 515 mm
Height: 387.8 mm (High)
352.5 mm (Low)
Depth: 199 mm
7.9 kg (with the stand) 6.1 kg (without the stand)
AC power cord × 2, Power cord holder × 1, Screw × 2 (for power cord holder)
21˝ wide, active matrix TFT
Width: 475 mm Height: 267 mm Diagonal: 545 mm
1920 × 1080
16.70 million
1000:1
DVI-D signal input (compatible with HDCP): DVI-D connector x 1 (compatible with DDC2B)
Digital signal input (compatible with EMBEDDED AUDIO/DUAL LINK signals):
Auto detection, 2 line, BNC connector x 2
Digital signal output (compatible with EMBEDDED AUDIO signals):
1 line switched out, BNC connector x 1
Input/output of composite signal:
1 line, BNC connector x 2,
1 V (p-p), 75 Ω
* The input (IN) and output (OUT) terminals are bridgeconnected (auto termination).
Input/output of analog component signal:
1 line, BNC connector x 6
Y: 1 V (p-p), 75 Ω
P /B-Y, P /R-Y: 0.7 V (p-p), 75 Ω
B R
* The input (IN) and output (OUT) terminals are bridgeconnected (auto termination).
Analog audio signal input: 1 line, RCA connector x 2, 500 mV (rms), high impedance
Analog audio signal output: 1 line, RCA connector x 2, 500 mV (rms)
☞ "Using the MAKE/TRIGGER system" on page 22
☞ "Using the serial communication" on page 24
SMPTE424M/SMPTE425M
SMPTE372M
BTA S-004C, SMPTE292M
ITU-R BT.656: 525/625
SMPTE259M: 525
SMPTE299M, SMPTE272M
without the stand
515 mm
347 mm
99.8 mm