Technical Data; Dimensions, Weights, Ambient Conditions; Supply Voltage (External); Control Signals - Balluff Micropulse BTL5-P Manual De Instrucciones

BTL5-P/I/K/L/M_-M_ _ _ _-A/B/Z-S32/KA_ _
Micropulse Linear Transducer - Rod Style
7

Technical Data

Typical values at DC 24 V and 25 °C. Ready for operation at once, full accuracy after warm-up. With magnet
BTL-P-1013-4R, BTL-P-1013-4S or BTL-P-1012-4R:
Resolution
Hysteresis
Repeatability
(resolution + hysteresis)
System resolution is determined by
the processor or external controller.
Recommended sampling rate:
Nominal length f
Standard
< 1000 mm 0.5 to 2 kHz
< 2000 mm 0.5 to 1 kHz
> 2000 mm 0.5 kHz
Non-linearity:
Nom. length < 500 mm > 500 mm
±100 µm ±0.02 % FS
Temperature coefficient
< (6 µm + 5 ppm * nominal length)/K
Shock loading 100 g/6 ms
per IEC 60068-2-27 1
Continuous shock 100 g/2 ms
per IEC 60068-2-29 1
Vibration 12 g, 10 bis 2000 Hz
per IEC 60068-2-6 1
(take care to avoid inherent reso-
nances of protective tube)
Pressure up to 600 bar
when installed in a
hydraulic cylinder
Individual specifications as per Balluff
1
factory standard
7.1 Dimensions, weights,
ambient conditions
Nominal length < 4000 mm
➥ ➥ ➥ ➥ ➥ Fig. 3-2
Dimensions
Weight ca. 2 kg/m
Housing anodized aluminum
Pressure tube Stainless steel 1.4571
diameter 10.2 mm
wall thickness 2 mm
e-modulus ca. 200 kN/mm
Mounting threads
M18 x 1.5 or 3/4"-16UNF
Operating temp. –40 °C to +85 °C
Humidity < 90 %, non-dewing
Protection rating per IEC 60529
IP 67 when closed up
8
english
< 2 µm 7.2

Supply voltage (external)

< 4 µm
Regulated supply voltage
< 6 µm
BTL5-_1... DC 20 to 28 V
Ripple
BTL5-_2... DC ±14.7 to ±15.3 V
Current draw
Inrush
Polarity reversal protection built-in
Overvoltage protection
Transzorb diodes
Electric strength
GND to housing
7.3

Control signals

INIT pulse
Level
Length
7.4

Connection to processor

Shielded cable,
max. length 500 m, Ø 6 to 8 mm
7.5

Included in shipment

Transducer
7.6

Magnets

(order separately)
Magnets BTL-P-1013-4R,
BTL-P-1013-4S, BTL-P-1012-4R
Dimensions
Weight
Housing
Operating temp.
Included:
8 mm spacer
Material POM (polyoxymethylene)
Magnets BTL5-P-4500-1
(Electromagnet)
Weight
Housing
2
Operating temp.
7.7

Mounting nuts

(order separately)
Mounting nuts M18*1,5
BTL-A-FK01-E-M18X1,5
Mounting nuts 3/4"-16UNF
BTL-A-FK01-E-3/4"-16UNF
< 0.5 V
pp
< 90 mA (at 1 kHz)
< 3 A/0.5 ms
500 V
+5 V RS 485/422 driver
1 µs (max. 3 µs)
➥ ➥ ➥ ➥ ➥ Fig. 3-2
➥ ➥ ➥ ➥ ➥ Fig. 3-4
approx. 10 g
anodized aluminum
–40 °C to +85 °C
approx. 90 g
plastic
–40 °C to +60 °C
7.8

Accessories (optional)

➥ ➥ ➥ ➥ ➥ Fig. 4-1
Connectors
7.9 Compatible processors and
displays
... for BTL5-P1
Analog output processor cards:
BTM-A/E1 multi-channel processor
with 1 to 4 DC analog outputs
Digital output processor cards:
BTM-H11-240/340 with 23-bit par-
allel and BCD, Gray/binary or
SSD, Gray
Displays:
BDD-AM10-1-P display and control-
ler with 2 relay outputs
BDD-CC08-1-P display with 8
switching outputs