Electric Start - Power Stroke PS80310E Manual Del Operador

WARNING:
Gasoline and its vapors are highly flammable and
explosive. To prevent serious personal injury and property
damage, handle gasoline with care. Keep away from
ignition sources, handle outdoors only, do not smoke
while adding fuel, and wipe up spills immediately.
WARNING:
Always shut off engine before fueling. Never remove
fuel cap or add fuel to a machine with a running or hot
engine. Make sure the unit is sitting on a flat, level surface
and only add fuel outdoors. If the engine is hot, let the
unit cool for at least five minutes before adding fuel.
After fueling, immediately replace fuel cap and tighten
securely. Move at least 30 ft. from refueling site before
starting engine. Do not smoke and stay away from open
flames and sparks! Failure to follow these instructions
could result in a fire and cause serious personal injury.
WARNING:
Check for fuel leaks. A leaking fuel cap, tank, or lines
are a fire hazard and must be replaced immediately. If
you find any leaks, correct the problem before using the
product. Failure to do so could result in a fire that could
cause serious personal injury.
NOTE: This is a 4-cycle engine. Do not mix fuel and
lubricant together.
„ Mix fuel stabilizer with gasoline according to fuel stabilizer
manufacturer's directions.
„ Before removing the fuel cap, clean the area around it.
Remove the fuel cap.
„ Insert a clean funnel into the fuel tank then slowly pour
gasoline into the tank. Fill tank to approximately 1-1/2 in.
below the top of the tank neck (this allows for fuel
expansion).
„ Replace fuel cap and tighten until the cap "clicks".
„ Clean up any spills before starting the engine.
PUMP LUBRICANT
The pressure washer pump has been filled with sufficient
lubricant at the factory. You do not need to check or add
lubricant to the pump.

ELECTRIC START

This pressure washer model is provided with both electric
start and recoil start capabilities. Avoid prolonged cranking,
as it can damage the engine.
OPERATION
The battery provided is a nominal 12 volt sealed rechargeable
lead-acid battery and can be operated in any position without
leakage. It complies with non-spillable battery regulations.
NOTE: Brand new pressure washers are shipped with the
red female wire (+) disconnected. The cap must be removed
and the red female wire (+) must be connected to the positive
(+) terminal on the battery before the Electric Start feature
will work.
For initial battery connection, see Connecting/Disconnecting
Battery.
STARTING AND STOPPING THE PRESSURE
WASHER
See Figures 11 - 15.
NOTICE:
Do not run the pressure washer without water supply
connected and turned on, as this may damage the high
pressure seals and decrease pump life. Completely
unwind the hose from its reel or coil and make sure the
hose is not being restricted by tires, rocks, or any other
objects that may lessen or prevent water flow to the
pressure washer.
Before starting the engine:
„ Connect the battery.
„ Connect all hoses.
NOTE: Make sure the pressure washer's water intake
screen is in place and unclogged before connecting
garden hose.
„ Check all fluids (lubricant and gas).
„ Turn on the garden hose then pull the trigger to relieve air
pressure; hold the trigger until a steady stream of water
appears.
NOTE: Make sure the faucet is turned on fully and that
there are no kinks or leaks in the hose.
To start the engine:
„ Turn the fuel valve to the OPEN position.
„ Pull the choke out to the START position.
NOTE: -J IRKMRI MW [EVQ SV XLI XIQTIVEXYVI MW EFSZI ‡*
push the choke in to the RUN position.
„ Push in at the top of the engine switch to put it in the ON
position.
„ Slide down and hold the lock button while pushing the
engine switch to the START position.
NOTE: The battery may require charging before the
pressure washer can be started using only the engine
switch. The pressure washer can be started by pulling
the starter grip and rope.
Page 11 — English