Tabla de contenido
Publicidad
We congratulate you for choosing the ZED-L gear motor.
All the items in the vast Benincà range are the fruit of twenty years of experience in the sector of automatisms and of
a continuous search for new materials and state-of-the-art technologies.
For this very reason, today we are able to offer extremely reliable products which, thanks to their power, efficiency and
long life, fully satisfy the demands of the end user.
All our products are made in conformity with the regulations in force and are covered by guarantee.
Moreover, a TPL policy stipulated with a leading insurance company covers any damage to persons or things caused
by manufacturing defects.
For good operation of this automation, the overhead door must possess the following characteristics:
- good robustness and rigidity
- good balancing
- good sliding of the guides.
In any case, it must be possible to perform manual opening and closing with ease.
ZED-L is an automation for overhead doors with counterweights, for central or side assembly.
Compact and linear, the ZED-L gear motor adapts to any type of overhead door.
As well as guaranteeing maximum reliability, ZED-L offers a continuous, regular and silent movement.
It is easy to fit using screws or welding.
The gear motor is irreversible which ensures that the door can be closed without the use of electric locks.
In the event of a power cut the door may be released by simply turning a knob on the gear motor.
-
Straight arm AU.D or curved arm AU.C.
-
Pair of tubes L 1500 mm with bush and brackets AU.45Z (only for central assembly).
-
Keyed-on bush AU.45B (only for side assembly).
-
Tube L 150 mm with bush and bracket (for side assembly) AU.45T.
-
Straight arm with welded bush AU.D45 (avoids on-site welding of the bush AU.45B to the arm AU.D).
-
AU.45L connecting bush between the gear motor and the torque tube without welding (with a dowel) complete
with torque tube L 2000 mm.
N.B.: Together with the AU.D45 and the AU.G45, this accessory allows complete installation without making any
welds.
-
Coupling with bracket AU.G45 (allows the connection of the arm AU.D45 to the tube AU.45Z without welds).
-
External release with customized key ZED.E.
-
Release from inside/outside by means of a handle with customized key ZED.SE.
-
ZED.MS wire release.
5.1 Preface
The automation with only one motor and central assembly is recommended for overhead doors
or equal to 12 m
; for larger dimensions or for overhead doors with a built-in small door use 2 side motors.
2
5.2 Operation n° 1
After identifying the axis of rotation of the overhead door A, determine the axis R passing through the bottom at a dis-
tance of 100 mm (fig. 1); this is the axis of the splined shaft that comes out of the gear motor.
Then anchor the plate of the gear motor to the door following the indications in figs. 2 and 3.
5.3 Operation n° 2 (fig. 4).
Fix the plate P onto the upright or the upper cross member of the overhead door or onto the wall next to the arm of the
door. (In any case the arm B must be positioned between the upright and the arm of the overhead door; if this space is
insufficient, use the curved arm art. AU.C which allows you to work in axis with the arm of the overhead door.
5.4 Operation n° 3 (fig. 6).
Provisionally fix the bracket S with the tube T, inserted both into the bracket and into the splined shaft of the gear mo-
tor.
Measure the tube T so that it is aligned with the arm B.
Then cut the tube to size.
Now fix the bracket S with screws or rivets, taking care to set the tube T absolutely level.
16
Introduction
1. General information
2. General characteristics
3. Indispensable accessories for assembly
4. Additional accessories
5. Installing the automatism
with an area less than
Publicidad
Tabla de contenido
