Denon AVR-3802 Instrucciones De Operación página 11

2 Switch to the speakerconfiguration screen
3 Set whether or not speakers
are connected and, if so, their
size parameters
• Tuselectthe speaker
• Tu select the parameter
5peeker Configuration
_Front Sl_
Center SD,
Subwoo fer
Speaker C_nf isurllt ion
SI_ Bask
center sp
F_ont Sp
Subwoofer
SumxJnd Sp A
SUlrour_d I_ck Sp
S_J_round Sp B
Press the ENTER button to finalize the settong
NOTE:
• Select
='Large r' or
"Sr_qalF' l]ot according to the actual size of the speaker but according to the speakeE's
capacity for playing low frequency (bass sound below frequency set for the Crossover Frequency mode and
below) signals If you do not know, try comparing the sound at both settings (sett ng the volume to a Jevel
low enough so as not to damage the speakers) to determine the proper setting
This screen1 is displayed when using both surround speakers A and B
• At this screen preset the surround speakers to be used in the different surround modes
When either "Large" or "Small" has been set for both
speakers A and B on the System Setup Menu (when using
both A and B surround speakers), the surround speaker
setting screen appears
Select the surround speakers to be used in the different
surround modes
• Tu select the surround mode
• Tu select the surrou_ld speaker
A: When using surround speakers A
B: When using surround speakers B
A+B: When using both surround speakers A and B
Surround Sp $eLtlnz
REO _ 8 A+B
DSP [] 8 A+B
SIMULATION
EX_ IN [] e A+B
EnteE the setting
When "Front" is set to "Large" and "Subwoofer" is set to "Yes", the set switches to the
subwoofer mode
Speaker type setting when using both surround speakers A and B
If "Small" is set for either surround speakers A or B, the output is the same as when "Small" is set for both
A and B
This screen1 is displayed when using a subwoofer
• Set the crossover freque_lcy a_ld subwoofer mode according to the speaker system bei_lg used
Large ................. Select this when using speakers that have sufficient performance for reproducing bass 1
sound below the frequency set for the Crossover Frequency mode
Small ................. Select this when using speakers that do not have sufficient performance for reproducing
bass sound below the frequency set for the Crossover Frequency mode When this is set,
bass sound with a frequency below the frequency set for the Crossover Frequency mode
is sent to the subwoofer
When this setting is selected, low frequencies of below the frequency set for the Crossover
Frequency mode are assigned to the subwoofer
None ................ Select this when no speakers are installed
Y_s/No .............. Select "Yes" when a subwoofer is installed, "No" when a subwoofer is not installed
2spkrs/1 spkr Set the number of speakers to be used for the surround back channel
If the subwoofer has suff cient low frequency playback capacity, good sound can be achieved even when
"Small" is set for the front, center and surround speakers
/
For the majority of speaker system configurations, using the Small setting for all five main speakers and
Subwoofer On with a connected subwoofer will yield the best results
Select the "Crossover Frequency" mode
Select the Frequency
_Crossover Frequency
E1T_) 1OOHz 120_
Subwoofer Mode
• _lra_-_: LFE
"Main
Select the "Subwoofer Mode"
Select the sett ng
l Crossover Frequency
lOOHz 120_
_Subwoofer Mode
4_BIlFa_--B_: LFE
-€4aln
Ente_ the setting
The System Setup Menu reappears
11