Denon AVR-3802 Instrucciones De Operación página 23

2
1 1 5
2 3
Select the nput source to be played
Example: CD
(M_ir_ _n_t! !Remo_e control urfit)
To select the input source SO,ROE
when REC MULTI OUT or
TUNING PRESET is selected,
press the SOURCE button
then operate the input function iMan unit)
selector
Select the nput mode
• Selecting the analog mode
Press the ANALOG button to switch to the
analog nput
(Mair_ brfit/ (Remo[e con[rol ur_it)
• Selecting the external input (EXT IN) mode
Press the EXT IN (on the EXT IN button on
the remote control unit) to switch the external
input
(Msir_ brfit) (Remo[e con[rol u r_itl
• Selecting the AUTO, PCM and DTS modes
The mode switches as shown below each
time the INPUT MODE button is pressed
AUTO _ PCM _DTS
t
(Rerno_e contr.! un_tl
• Selecting the AUTO mode
Press the AUTO button to switch to the auto
mode
AJo
(M_ir_ _n_t!
4
1
@ @ @
3
2
input mode selection function
Different nput modes can be selected for the different
input sources The selected input modes for the separate
inputso ces are stored in the memory
_1 AUTO (auto mode)
In this mode, tl:e types of signals being input to the
digital and a aog rput jacks for the selected input
source are detected and the program in the AVR
3802's surro rd decoder is selected automatically
upon playback This mode can be selected for all input
sources other that PHONQ and TUNER
The presence or absence of digital signals s detected,
the s grals input to the digital input iacks are identified
and decoding and playback are performed
automaticaly n DTS, Dolby Digital or PCM (2 channel
stereo) format If no digital sgnal s being input, the
analog input acks are selected
Use this mode to play Dolby Digital s grals
_2 PCM (exclusive PCM signal playback mode)
Decoding and playback are only performed when PCM
signals are beng input
Note that noise may be generated when using this
mode to play signals other than PCM sgras
_3) DTS (exclusive DTS signal playback mode)
Decoding and playback are only performed when DTS
signals are beng input
ANALOG (exc}usve analog audio signal payback
mode)
The signals input to the anaog inpt iacks are decoded
and olayed
_5 EXT IN (external decoder input jack selection mode)
The signals beng rp ttothe externaldecoder input
iacks are played without pass ng through the surround
circuitry
NOTE:
• Note that noise will be output when CDs or LDs
recorded r DTS format are played in the "PCM r'
(exclusive PCM signal payback) or "ANALOG"
(exclusive PCM sgnal playback) mode Select the
AUTO or DTS mode when playing sigras recorded in
DTS from a laser disc player or CD player
Note on playing a source encorded with DTS
• Noise may be generated at the beginning of
playback and while searching during DTS
playback in the AUTO mode. If so, play in the
DTS mode,
3
• Selecting the PCM mode
Press the PCM button to switch to the PCM
signal input
PCr_
(Main unit)
• Selecting the DTS mode
Press the DTS button to switch to the DTS
signal input
(Main uait)
Select the play mode
Example: Stereo
_,_E
Input mode display
• In the AUTO mode
/1\
• In the DIGITAL PCM mode
o @ o
• In the DIGITAL DTS mode
o o ©
One o_ these ligr_ts depel_d_ng on
the u_put sigr_al
Input signal display
• DOLBY DIGITAL
• DTS
(Mair_ _nit) (Remote cor_t_o_ _nit) • POM
_4 Tu select the surround mode o*aos_-,
while adjusting the surround
paraTnete_s, channel volume or
tone control, press the
surround mode button then Mail dr1)
operate the selector
Start playback on the selected component
• For operating instructions, refer to the
component's manual
Adjust the volume
The volur le leve is
dspayed or tie (MaJr _rlt!
r laste volur le leve
ds ay
(Remote cor_tlo_ _nit/
The volume can be adjusted within the range of
-70 to0to18dB, nstepsof 1 dB However, when
the channel level is set as described on page 13 or
page 27, f the volume for any channel is set at +1
dB or greateh the volume cannot be adjusted up to
18 dB (In this case the maximum volume
adjustment range is "18 dB --/Maximum value of
channel level)")
Input mode when playing DTS sources
• Noise will be output if DTS-compatible CDs or LDs
are played in the "ANALOG" or "PCM" mode
When playing DTS-compatibb sources, be sure to
connect the source component to the digtal input
jacks (OPTICAL/COAXIAL) and set the input mode to
"DTS"
The _ ndcator lights when digital signals
are being input properly If the _ ndicator
does not light, check whether the digtal input
component setup (page 14) and connections are
correct and whether the component's power is
turned on
NOTE:
• The _ indicator will light when playing
CD-ROMs containing data other than audio
signals, but no sound will be heard
23