Denon AVR-3802 Instrucciones De Operación página 36

[] LAST FUNCTION MEMORY
• This unit is equipped with a last function memory which stores the nput and output setting conditions as the'
were mmediately before the power s switched off
This function eliminates the need to perform compJicated resettings when the power is switched on
• The unit is also equipped with a back-up memory This function provides approximately one week of memor
storage when the main unit's power switch is off and with the power cord disconnected
[] INITIALIZATION OF THE MICROPROCESSOR
When the ndication of the display is not normal or when the operation of the unit does not shows the reasonable
result, the init alization of the microprocessor is required by the following procedure
1 Switch off the unit using the main unit's power
operation switch
2 Hold the following AUTO button and PCM
button, and turn the main unit's power
operation switch on
3 Check that the entire d splay is flashing with an
interval of about I second, and release your
fingers from the 2 buttons and the
microprocessor will be initialized
NOTES:
• If step 3 does not work, start over from step 1
• If the microprocessor has been reset, all the
button settings are reset to the default values
(the values set upon shipment from the factory)
,/O
1,2 2
[] TROUBLESHOOTING
If a problem should arise,first check the following,
1. Are the connections correct ?
2. Have you operated the receiver according to the Operating Instructions ?
3. Are the speakers, turntable and other components operating property ?
If this unit is not operating properly, check the items listed in the table below Should the problem persist, there
may be a malfunction
Disconnect the power immediately and contact your store of purchase
2
Z
o
S
£
8
#
Symptom
D]SPLAY not it an(J sound not
arod ce(J w_'en power swtch set
to o;_
DISPLAY I;€ but soul/d rlot
produced
DISPLAY not lit and power
ndicator s flashJ/g rapidly
Sound produced only from one
channel
Posit;ons ofinstruments
[eversed during stereo
playback
The on screen display is not
displayed
Humming i/o[se produced when
lecordisplay_ng
owing noise produced when
volume is hg/
Cause
• Power cord T1Ot plugged in
securely¸
• Speaker cords not securely connected
• mp_ope positio/ of the audio
function butCon
• Volume co_/trol set to mJ_/i_/lu_/1
• MUTING is on
• Digita signas not input Digital i/put
selected
• Speaker terminals are short
c;rcuked
• Block the ventilation holes of the
set
• The unt is operating at cor/tll/Uous
h]gl power conditions and/or
[fladequate vendlat o /
• Incomplete connectlo_/ of speaker
cords
• Incomplete co_/nectlof_ ol
illput/output cords¸
• Reverse connections of eft and
right speakers or left and right
[flput/output cords
• "On screen d splay' is set to off o/
the system setup menu screen
• G¢ourld wire of tu /table not
connected prope ly
• Incor'lplet e PHONO jack
cofsnect on
• TV or radio transmlsso/ antenna
nearby
• Turntable and speake systems too
cose togethe
• FIool is ul/stable al/d viblates easily¸
• Stylus pressu e too wea
• Dust or drt on stylus
• Caltfldge defective¸
Measures
• Check tile insertion of tile powe
cord plug
• Turfs the power OTS wth the remote
contro unit after tum/g the
POWER switch oil
• Connect seourey
• Set to a su table posit on
• Tur/- volume up to Sb[table leve
• Swtch off MUTING
• Input digital sigllals or select input
iacks to which digita_ signals are
being input¸
• Swtch powe of l, connect speakers
properly, then switch power back
• Turn off the set's power, then
venti}ate t wel} to cool it down
Once the set is cooled down turfs
the power back on
• Turn off the act's powel therl
venti}ate t wel} to cool it down
Once the set is cooled dow/ turn
the power back on
• Cofsnect securely
• Cof_neet securely
• C/eck left and rg/t connect o/s
• Set "on screen display" on the
system setup menu screen to on
• Cof_nect securey
• Co/fsect securely
• Co/tact you store of pure/use
• Separate as much as possible
• Use cushiOflS to absorb Speaker
vibrations transmitted by flool If
turntable is not equipped whh
insulators, use audio insulators
(commonly available)
• Apply proper styus pressure
• C/eck stylus
• Replace calt/idge
Page
4
22
8
3,7
3,7
Sound is d[storCed
• MC ca_tr dge beng used • Replace wtll MM carCddge or use a 4
Volume is weak head amplifier or step up
traT_sformer
8
48
15
4
4
36