Denon AVR-3802 Instrucciones De Operación página 17

I_i'l
Use the mode selector buttons to select the component you want
to
operate¸
The mode switches between "AMP", "TUNER" and "MULTI"
each time the RECEIVER button is pressed, between "CDR",
"MD" and "TAPE" each time the CDR/MD/TAPE button is
pressed, between "DBS" and "CABLE" each tree the
DBS/CABLE button is pressed, and between "DVD" and "DVD
SETUP" each time the DVD button s pressed, and between
"VCR" and "VCR2" eacht me the VCR button is pressed
1
Operate the audio component
• For details, refer to the component's operating instructions
It may not be possible to operate some models
1. CD player (CD} system buttons 2. Tape deck (TAPE) system buttons
@@@
@ @ @
®®@
44 I_1_ : Manual search (forwa d and everse)
• : Stop
I)- : P}ay
1"_41, !)_l_l : Auto searc/ (te beg[nn ng of track)
II : Pause
SKIP +, (for CD changes only)
09,+10 : lOkey
44 Rewnd
I_1_ Fast forward
• Step
I b Forward play
II Pause
14141 Reverse play
A/B Switch between sides A and B
4, Tuner system buttons
3, MD recorder (MD}, CD recorder (CDR) system
buttons
@ @ @
® @
® ® @
4141 I_1_ : Manual search (forwa d and everse)
• : Stop
I)- : P}ay
1"_41, I)_1_1 : Auto searc/ (te beg[nn ng of track)
II : Pause
09,+10 : lOkey
TUNING 3, :
BAND
MODE
MEMORY
SHIFT
CHANNEL+,
1-8
RDS
PTY
RT
© @ @
© @ ®
Tuning up/dewn
Switc / between AM and FM bands
Switch between AUTO and MONO
Preset memory
Switch preset channel range
Preset channel _p/dewn
10key
RDS search
PTY search
Radio Text
By using the preset memory, the included remote control unit can be used to control other makes of video
equipment Note that this is not possible for some models, however In such cases, use the learning function
(see page 19) to store the remote control signals in the remote control unit's memory
See page 20 for instructions on resetting the data stored in the preset memory
Press the power ON/SOURCE button and the
OFF button at the same time
• "SET UP" appears on the remote control
unit's display
Press the ENTER button
Use the s and cursor buttons to display
"ENTER CODE" on the remote control unit,
then press the ENTER button
The remote control unit's display swiLches
as follows each time the • and cursor
buttons are pressed
1
4
_ENTERCODE
CODENO
i
LEARN
i
SYSCALL
i
RESET
AUTO SEARCH
After "SEL MODE" s dsplayed, the last
selected mode is set Use the A and cursor
buttons to display the component whose codes
you want to store in the memory, then press
the ENTER button
The display switches as shown below each
time the , and cursor buttons are
pressed
3,4
2,3,4
5
Referring to the included List
© (9 (9
of Preset Codes, use the
(9 (9 (9 number buttons to input the
(9 _ i_'_ preset code (a 4-digit
number) for the manufacturer
of the component whose
signals you want to store in
the memory
"OK" is displayed when the signals are
reg stered and the mode is terminated
To store the codes of another component in the
memory, repeat steps 1 to 6
NOES:
• The signals for the pressed buttons are emitted while setting the preset memory Tu avoid accidental
operation, coveE the remote control unit's transmitting window while setting the preset memory
• Depending on the model and year of manufacture, this function cannot be used for some models, even if
they are of makes listed on the included list of preset codes
• Some manufacturers use more than one type of remote control code Refer to the included list of preset
codes to change the number and check
17