Bosch Active Line Serie Manual Original página 59

English–9
Switching the Walk Assistance On/Off
The walk assistance can make it easier for you to push the
eBike. The speed of this function depends on the selected
gear and can reach a maximum of 3.7 mph. The lower the
selected gear, the lower the speed of the walk assistance
function (at full capacity).
 Using the walk assistance function is only recom-
mended when pushing the eBike. There is risk of injury
if the wheels of the eBike are not in contact with the
ground while using the walk assistance.
To activate the walk assistance function, briefly press but-
ton "WALK" on your on-board computer. After activation,
press button "+" within 3 s and keep it pressed. The eBike
drive is switched on.
Note: The walk assistance cannot be activated in the "OFF"
assistance level.
The walk assistance is switched off as soon as one of the
following occurs:
– you release the button "+" 13,
– the wheels of the eBike are stopped (e.g. by actuating
the brakes or impacting against an obstacle),
– the speed exceeds 3.7 mph.
Note: On some systems the walk assistance function can
be started directly by pressing the "WALK" button.
Speed and Distance Indicator
The speed indicator f always displays the current speed.
The following functions are available in the function indica-
tor (combination of text indicator d and value indicator e):
– "Clock": Current time
– "Max. speed": Maximum speed achieved since the last
reset
– "Avg. speed": Average speed achieved since the last
reset
– "Trip time": Trip time since the last reset
– "Range": Estimated range of the available battery pack
charge (for constant conditions such as assistance lev-
el, route profile, etc.)
– "Odometer": Display of the total distance traveled with
the eBike (cannot be reset)
1 270 U20 XBI | (20.4.16)
116
– " NuVinci Cadence/Gear": This menu item is dis-
played only in conjunction with a Nu Vinci H|Sync auto-
matic transmission.
If you press the "i" button for longer than 1 s, you will ac-
cess the NuVinci menu item from any menu item in the
information menu.
To switch from the " NuVinci Cadence" mode to the
" NuVinci Gear" mode, press the "i" button for 1 s.
To switch from the " NuVinci Gear" mode to the
" NuVinci Cadence" mode, all you have to do is brief-
ly press the "i" button.
The default setting is " NuVinci Cadence".
Range Odometer NuVinci Cadence
(1 s)
(1 s)
NuVinci Gear
– "Gear": This menu item appears only in conjunction
with a Shimano-Di2 gear hub. The currently engaged
gear of the transmission is shown on the display. The
newly engaged gear will be shown briefly on the display
whenever the gear is shifted.
– " Autom. Gear Selection": This menu item appears
only in conjunction with an SRAM automatic transmis-
sion.
Range Odometer Gear: Auto
(1 s)
(1 s)
Gear
By pressing the "i" button for more than 1 s, you can
switch back and forth between the " Autom. Gear
Selection" automatic mode and the " Gear" manual
mode.
If you are in first gear in manual mode, you can also
press the "–" 12 button to go to the " Autom. Gear
Selection" mode. By pressing the "–" 12 button again,
you can switch back to the manual mode. It is also pos-
sible to access the manual mode by pressing the "+" 13
button.
– "Trip distance": Distance covered since the last reset
Bosch eBike Systems
To switch between the indication functions, press the "i"
button 1 on the on-board computer or the "i" button 11 on
the operating unit until the desired function is displayed.
To reset "Trip distance", "Trip time" and "Avg. speed",
switch to any of the three functions and then press and hold
the "RESET" button 6 until the indicator is set to zero. This
also resets the values for the other two functions.
To reset the "Max. speed", switch to this function and then
press and hold the "RESET" button 6 until the indicator is
set to zero.
To reset "Range", switch to this function and then press
the "RESET" 6 button until the display is reset to the value
of the factory setting.
When the on-board computer is removed from the holder
4, all function values remain stored and can be viewed.
Displaying/Adapting Basic Settings
The basic settings can be displayed and changed regard-
less of whether the on-board computer is inserted in the
holder 4 or not. Some settings are visible and changeable
only when the operating computer is inserted. Some menu
items may be missing depending on the equipment of your
eBike.
To access the basic settings menu, press and hold the
"RESET" button 6 and the "i" button 1 until "Configura-
tion" is displayed in text indicator d.
To switch between the basic settings, press the "i" but-
ton 1 on the on-board computer until the desired basic set-
ting is displayed. When the on-board computer is inserted
in holder 4, you can also press the "i" button 11 on the op-
erating unit.
(1 s)
To change the basic settings, press the On/Off button 5
next to the "–" indicator to decrease the value or scroll
down, or the light button 2 next to the "+" indicator to in-
crease the value or scroll up.
When the on-board computer is inserted in holder 4, you
can also change the values with the "–" button 12 or the
"+" button 13 on the operating unit.
To exit the function and store a changed setting, press the
"RESET" button 6 for 3 s.
The following basic settings are available:
– "– Clock +": The current time can be set here. Pressing
and holding the setting buttons fast-forwards the setting
speed.
– "– Wheel circum. +": You can change this value pre-set
by the manufacturer by ±5 %. This menu item is dis-
played only when the on-board computer is in the
holder.
Bosch eBike Systems
English–10
– "– English +": You can change the language of the text
indications. You can choose between German, English,
French, Spanish, Italian, Portuguese, Swedish, Dutch
and Danish.
– "– Unit km/mi +": The speed and distance can be dis-
played either in kilometers or miles.
– "– Time format +": The time can be displayed either in
a 12-hour or 24-hour format.
– "– Shift recom. on/off +": You can switch the indica-
tion of a shift recommendation on and off.
– "Power-on hours": Indicates the total travel time with
the eBike (can not be changed).
– "Gear calibration" (only NuVinci H|Sync): Here you
can calibrate the continuously variable transmission.
Confirm the calibration by pressing the "Bike lights" but-
ton. Then follow the instructions.
In the event of an error, it can also be necessary to per-
form calibration when riding. In this case, you also con-
firm the calibration by pressing the "Bike lights" button
and then follow the instructions on the display.
This menu item is displayed only when the on-board
computer is in the holder.
– "– Start gear +": The starting gear can be set here. The
automatic shift-back function is switched off in the "––"
position. This menu item is displayed only in connection
with SRAM DD3 Pulse and Shimano Di2. This menu item
is displayed only when the on-board computer is in the
holder.
– "Gear adjustment": This menu item can be used to per-
form fine adjustment of the Shimano Di2. The pre-de-
fined adjustment range can be found in the operating in-
structions provided by the drivetrain manufacturer.
Perform fine adjustment as soon as you hear unusual
sounds coming from the drivetrain.This will prevent pre-
mature wear of the drivetrain and also avoid any deteri-
oration in shifting behavior which could cause you to fall
in adverse situations. This menu item is displayed only
in conjunction with Shimano Di2. This menu item is dis-
played only when the on-board computer is in the
holder.
– "Displ. vx.x.x.x": This is the software version of the dis-
play.
– "DU vx.x.x.x": This is the software version of the drive
unit.This menu item is displayed only when the on-board
computer is in the holder.
– "DU # xxxxxxxxx": This is the serial number of the drive
unit. This menu item is displayed only when the on-
board computer is in the holder.
1 270 U20 XBI | (20.4.16)
117