Comm. And Options - Danfoss VLT AutomationDrive FC 302 Manual De Funcionamiento

Programación
6.4.2 5-** E/S digital
Par. nº # Descripción del parámetro
5-0* Digital I/O mode
5-00 Digital I/O mode
5-01 Terminal 27 mode
5-02 Terminal 29 mode
5-1* Digital Inputs
5-10 Terminal 18 digital input
5-11 Terminal 19 digital input
5-12 Terminal 27 digital input
6 6
5-13 Terminal 29 digital input
5-19 Terminal 37 safe stop
5-3* Digital Outputs
5-30 Terminal 27 digital output
5-31 Terminal 29 digital output
5-4* Relays
5-40 Function relay
5-41 On delay, relay
5-42 Off delay, relay
6.4.3 8-** Comunic. y opciones
Par. nº # Descripción del parámetro
8-0* General Settings
8-01 Control site
8-02 Control word source
8-03 Control word timeout time
8-04 Control word timeout function
8-05 End-of-timeout function
8-06 Reset control word timeout
8-3* FC Port Settings
8-30 Protocol
8-31 Address
8-32 FC port baud rate
8-33 Parity/stop bits
8-35 Minimum response delay
8-36 Max response delay
8-37 Max inter-char delay
8-4* FC MC Protocol Set
8-42 PCD write configuration
8-43 PCD read configuration
8-5* Digital/Bus
8-53 Start select
8-55 Set-up select
108
Manual de funcionamiento
Valor predeterminado
[0] PNP
[0] Input
[0] Input
[8] Start
[0] No operation
[0] No operation
[0] No operation
[1] Safe Stop Alarm
[0] No operation
[0] No operation
[0] No operation
0.30 s
0.30 s
Valor predeterminado
[0] Digital and ctrl.word
null
1.0 s
[0] Off
[1] Resume set-up
[0] Do not reset
[1] FC MC
2 N/A
[2] 9600 Baud
[0] Even parity, [1] Stop
bit
10 ms
5000 ms
25 ms
[1685] FC port CTW 1
[1603] Status word
[3] Logic OR
[3] Logic OR
Danfoss A/S © Rev. 07-02-2014 Reservados todos los derechos.
4-set-up (4 Cambio
ajustes) durante conversión
funciona-
miento
All set-ups FALSE
All set-ups TRUE
All set-ups TRUE
All set-ups TRUE
All set-ups TRUE
All set-ups TRUE
All set-ups TRUE
1 set-up TRUE
All set-ups TRUE
All set-ups TRUE
All set-ups TRUE
All set-ups TRUE
All set-ups TRUE
4-set-up (4 Cambio
ajustes) durante conversión
funciona-
miento
All set-ups TRUE
All set-ups TRUE
1 set-up TRUE
1 set-up TRUE
1 set-up TRUE
All set-ups TRUE
1 set-up TRUE
1 set-up TRUE
1 set-up TRUE
All set-ups TRUE
All set-ups TRUE
1 set-up TRUE
1 set-up TRUE
All set-ups TRUE
All set-ups TRUE
All set-ups TRUE
All set-ups TRUE
Índice de Tipo
- Uint8
- Uint8
- Uint8
- Uint8
- Uint8
- Uint8
- Uint8
- Uint8
- Uint8
- Uint8
- Uint8
-2 Uint16
-2 Uint16
Índice de Tipo
- Uint8
- Uint8
-1 Uint32
- Uint8
- Uint8
- Uint8
- Uint8
0 Uint8
- Uint8
Uint8
-3 Uint16
-3 Uint16
-3 Uint16
Uint16
Uint16
- Uint8
- Uint8
MG37A205