Tractel rollclamp Serie Manual De Instalación, De Utilización Y De Mantenimiento página 13

3. If a preliminary study data package has been
prepared, the installer must have this data package
in hand (§ 7).
8.2. Preliminary checks prior to
installation
Before you begin to install the system, check the
following:
General check:
1. All the markings are present and are legible
(see § 11).
2. The various components forming the anchor device
are present and do not show any significant signs of
deformation, wear and/or corrosion.
3. All components of the fall arrest system are used
in compliance with the recommendations of their
respective manuals.
4. The anchor device has been covered by a periodic
inspection over the past 12 months.
5. The clearance (fig. 4, item T) must be compatible
with the person's fall arrest device.
6. The anchoring beam planned (fig. 2, item 10) is
compatible with the size of the anchor device to be
installed (Fig. 2).
rollclamp additional check:
1. The securing strap (fig. 1.1, item 8) does not show
any signs of wear or damage.
2. The mobile jaw (fig. 1.1, item 3) locks correctly on
the guide rod (fig. 1, item 7).
3. The 4 guide rings are in place (fig. 1.1, item 1).
4. The 2 (M model) or 4 (L model) guide shoes are in
place (fig. 1.1, item 2).
rollbeam additional check:
1. The securing anchor point (fig. 1.2, item 13) does
not show any signs of wear or damage.
2. The clamping pads (fig. 1.2, item 4) are in place
and the locking crews (fig. 1.2, item 5) are correctly
tighten.
3. The 4 guide rollers (fig. 1.2, item 1) turn freely.
corso additional check:
1. The securing anchor point (fig. 1.3, item 13) does
not show any signs of wear or damage.
2. The flange hooks (fig. 1.3, item 1) are correctly
hang on the beam.
3. The adjustable hand lever (fig. 1.3, item 4) is
correctly tighten.
The following table indicates the dimensional features
A and B of the beam shown in Figure 2 in relation to all
anchor device models.
A (mm)
min
rollclamp M
90
rollclamp L 200
rollbeam SB 58
rollbeam LB 220
corso 75
DANGER
If any anomaly is observed during these checks,
the anchor device must be removed from service
and confined to prevent any use and should be
repaired by a qualified technician (see § 11-3).
8.3. Installation
The anchor devices are installed in 3 steps:
– Opening of the anchor device.
– Installation of the anchor device on the beam.
– Check after installation.
8.3.1. Opening the anchor device
rollclamp
(fig. 5.1, item 1)
1. Unlock the indexing knob (fig. 1.1, item 4) by
positioning the notch as shown (fig. 5).
2. Release the mobile jaw (fig. 1.1, item 3) by pulling
on the indexing knob (fig. 1.1, item 4).
3. Slide the mobile jaw (fig. 1.1, item 3) while holding
the indexing knob (fig. 1.1, item 4).
4. Lock the mobile jaw (fig. 1.1, item 3) on the guide
rod (fig. 1.1, item 7) by releasing the indexing knob
(fig. 1.1, item 4).
DANGER
Check that the indexing knob pin (fig. 1.1, item 4)
is properly engaged in an indexing hole (fig. 1.1,
item 9) of the guide rod (fig. 1.1, item 7).
rollbeam (fig. 5.2, item 1)
1. Positioning the anchor bar center (fig. 1.2, item 8)
on the same center as the adjustable flanges thread
hole as shown (fig. 5.2).
2. Turn the anchor bar clockwise to screw it inside
adjustable flanges (fig. 1.2, item 3) thread hole.
B (mm)
max min max
400 8.5 40
615 9.5 95
220 8 20
300 8 20
235 8 20
13
GB