Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
27. To install an anchor device on a beam supporting
electrical cables, compressed air pipes, or other.
28. To use an anchor device for any use other than as
an anchor point for a PPE.
14. Equipment Compliance
TRACTEL SAS RD 619 – Saint-Hilaire-sous-Romilly
– F-10102 Romilly-sur-Seine France hereby declares
that the safety equipment described in this manual,
• complies with the requirements of European regulation
UE 2016/425 of March 2016.
• is identical to the PPE, having been subject to the
"CE"-type-examination certificate issued by the
APAVE SUDEUROPE SAS – CS 60193 – 13322
Marseille – France, identified under the number 0082,
and tested according to the 2012 EN 795 standard.
• is subject to the procedure referred to in Annex VIII
of the EU Regulation 2016/425 of the European
Parliament, Module D, under the control of a notified
body: APAVE SUDEUROPE SAS – CS 60193 – 13322
Marseille – France, identified under the number 0082.
15. Marking
The marking on each product indicates:
a:
the trade name: Tractel
b:
the name of this equipment.
c:
the referenced standard.
d:
this equipment reference.
e:
CE
Logo
followed
identification number of the approved body
responsible for production control.
f:
Year and month of manufacture.
g:
the serial number.
h:
a pictogram showing that the manual must be read
before use.
W: Maximum operating load.
p:
maximum number of operators.
aa.: date of next periodic inspection.
16. Periodic inspection and repair
An annual periodic inspection is required, but depending
on the frequency of use, environmental conditions
and regulations of the company or the country of use,
periodic inspections may be more frequent.
Periodic inspections should be carried out by an
authorised and competent technician, in compliance
with the manufacturer's instructions transcribed in the
file "Tractel
PPE inspection instructions".
®
Confirmation of the legibility of the product markings
should be an integral part of the periodic inspection.
On completion of the periodic inspection, the return to
service must be indicated in writing by the authorised
.
®
by
the
number
0082,
and competent technician who carried out the
inspection. This return to service must be recorded on
the inspection sheet in the middle of this manual. This
inspection record should be retained throughout the
product's life cycle, up until it is recycled.
After arresting a fall, this product must undergo a
periodic inspection as described in the current article.
The product's textile components must be changed,
even though they may not display any visible changes.
17. Lifespan
TRACTEL
textile PPE equipment, such as harnesses,
®
lanyards, ropes and energy absorbers, TRACTEL
Mechanical PPE equipments as stopcable™ and
stopfor™
fall-arresters,
fallarresters, and the TRACTEL
without restrictions from their manufacturing date
providing that:
– Normal use in accordance with the recommendations
for use given in this manual.
– A periodic inspection, which must be performed at
least once a year by an approved and competent
technician. On completion of this periodic inspection,
it must be certified in writing that the PPE is fit to be
returned to service.
– Strict compliance with the storage and transport
conditions contained in the current manual.
– As a general rule and subject to the application of the
conditions of use mentioned above, their lifespan may
exceed 10 years.
18. Withdrawal from service
When disposing of the product, all components must
be recycled by firstly sorting them into metallic and
synthetic materials. These materials must be recycled
by specialist bodies. During disposal, dismantling and
separating the components should be undertaken by a
duly trained person.
Manufacturer's name and address:
Tractel SAS - RD 619 - BP 38
Saint Hilaire sous Romilly
10102 Romilly sur Seine
France
®
blocfor™
self-retracting
lifelines can be used
®
17
GB
Publicidad
Tabla de contenido
