Inspecting The Press Tool And Attachments - RIDGID MegaPress Manual Del Operador

MegaPress
Catalog No. Description
37973 1 1 / " MegaPress Ring
4
37978 1 1 / " MegaPress Ring
2
37983 2" MegaPress Ring
21878 V2 Actuator
V2 Actuator Arm
V2 Actuator Spherical Tip
V2 Side
Plate
V2 Actuator
Torsion
Spring
(Not
Visible)
RIDGID V2 Actuator
Figure 2 – MegaPress Ring and V2 Actuator
Only use RIDGID Press Tools and RIDGID
WARNING
press tool attachments (jaw sets, rings, actuators, etc.)
when specified by the fitting manufacturer for use with their
system. Use of incorrect press tools and/or attachments for
a system can cause system leaks, damage the press
tool or attachment, void warranties or cause severe per-
sonal injury.
NOTICE Contact the fitting manufacturer for specific
information on their system, including compatible pipe,
materials, installation instructions, minimum distance
between fittings, seal material, inspection, testing, etc.
Incorrect installation can cause system leaks and exten-
sive property damage.
Contact RIDGID Technical Services Department at (800)
519-3456 or rtctechservices@emerson.com for a list of
press fitting system and valve manufacturers that specify
RIDGID pressing tools and attachments for their sys-
tems.
Inspecting The Press Tool and
Attachments
WARNING
Inspect your pressing tool and attachments daily
and correct any problems to reduce the risk of seri-
ous injury from electric shock, tool and attach-
4
® Fitting System
Weight
5.99 lbs (2,72 kg)
6.46 lbs (2,93 kg)
5.77 lbs (2,62 kg)
4.7 lbs (2,13 kg)
MegaPress Press
Ring Pivot Pin &
Press Ring
Torsion Spring
Actuator Pocket
(Not visible)
(Not Visible)
MegaPress Press Ring
ment failure and other causes and to prevent tool
and property damage.
1. Inspect press tool according to the specific tool oper-
ator's manual.
2. Clean any oil, grease or dirt from the tool and attach-
ments, especially the handles and controls. This
reduces the risk of the tool or attachment slipping from
your grip and makes inspection easier.
3. Closely inspect all pressing attachment components
(jaw sets, rings, actuators, etc.) for any cracked, bro-
ken, worn, missing, mis-aligned or binding parts or
any other sign of damage that may prevent proper
and safe operation. Damaged parts can cause the
attachment to make incorrect pressed connections or
fail during use, and cause serious injury or property
damage. If any damage is found, the attachment
should be discarded and replaced.
Always discard the complete pressing
WARNING
attachment. Never replace individual components or
exchange parts between assemblies. Failure to replace
the entire assembly may result in component failure
and serious injury.
Do not modify pressing attachments or use modified
attachments. A pressing attachment component that
has been welded, ground, drilled or modified in any
manner can shatter during pressing, resulting in sharp
flying objects, severe injury or death. Discard and
replace damaged pressing attachments.
4. Inspect the attachment markings to make sure that it
is clearly marked as to the system and size that it is
appropriate for. Do not use an attachment that is
not clearly marked.
5. Inspect the press profile of the attachment. If it is
rusty, dirty or if there is a build up of fitting material,
clean as described in the maintenance section. It is
important to keep the press profile clean to prevent
the formation of burrs during pressing process, pre-
vent the attachment from sticking to the fitting and
make sure that a proper press connection is made.
6. Make sure that springs are intact and bias the attach-
ment in the proper direction (closed for rings, jaws and
actuators). Attachment should cycle freely from the
fully open to fully closed position. If needed, lubricate
pivot points with a light lubricating oil. Wipe any
excess oil from the attachment.