Technical Data; Power Requirements - Truper EXPERT SOMU-200X Instructivo

Technical Data

Voltage
Current
Welder Process
Open Circuit Voltage
Current Range
Duty Cycle
Micro Wire Diameter
Micro Wire speed
Electrode diameter
Cooling Type
Insulation
Conductors
WARNING
Avoid the risk of electric shock or severe injury. When the power cable gets damaged
it should only be replaced by the manufacturer or at a
The build quality of the electric insulation is altered if spills or liquid gets into the tool while in use.
Do not expose to rain, liquids and/or dampness.
Before gaining access to the terminals all power sources should be disconnected.
WARNING

Power Requirements

WARNING If faults or breakdowns happen. Ground connection offers a
trajectory with minimum resistance for electric power. It reduces the risk of electric
shock. This tool is built with a power cable with an earth conductor and a plug with
ground connection. The plug shall be connected into a power outlet installed and
grounded according to all local codes.
WARNING Do not modify the plug supplied. If the plug cannot be fitted
to the socket, have a qualified electrician to install the suitable socket.
• When using the welder together with more tools using the same ground connect those in parallel, never connect a
series.
CAUTION
• The gauge of the ground conductor cable shall not be of a smaller gauge than the power supply cable.
CAUTION
• Connection to the power supply shall only be carried out by a professional electrician.
• Double check the input connection voltage stipulated in the welder nameplate matches the power
CAUTION
supply voltage.
CAUTION
• The power supply cord shall meet the following requisites:
Switch
Fuse (Work Rated Current)
Electric Wire
* The current for fuse fusion is double of its rated current.
SOMU-200X
Code
17258
110 V / 220 V
40 A / 27 A
MIG : 63 V c.c - 65 V c.c. | TIG: 13 V c.c. | SMAW : 63 V c.c - 65 V c.c.
110 V 14 A - 90 A
MIG :
220 V 14 A - 200 A
SMAW : 110 V Type: 6013
220 V Type: 6013
220 V Type: 7018
TIG : 0,039" | 0,062" | 0,078"
Class I
30 A
30 A ( * )
2,5 mm
2
Description
Input
Input Rated Capacity
Output
MIG, TIG y SMAW
110 V 8 A - 90 A
| TIG :
220 V 8 A - 180 A
110 V 80% - 8 minutes' work per 2 minutes' rest.
220 V 40% - 4 minutes' work per 6 minutes' rest.
The output values are given in a 68 ºF temperature.
In higher temperatures, the duty cycle may be reduced.
0,023" | 0,031" | 0,035" | 0,039"
86.6 in/min - 535.4 in/min
3/32"
3/32" | 1/8" | 5/32" | 3/16"
3/32" | 1/8" | 5/32"
MIG : 0,023" | 0,031" | 0,035" | 0,039"
Fan Forced
IP Grade
12 AWG x 3C with 221 °F insulation temperature.
Power cord grips used in this product: Type "Y".
Build quality: Basic insulation
Thermal insulation on motor winding: Class F
• If extensions between the welder and the work piece
are needed, the soldering cable gauge shall be increased
to keep the welder energy output with a potential drop
not higher than 4 V
Multi process welder
Frequency
110 V 8 A - 70 A
| SMAW:
220 V 8 A - 180 A
IP21S
Authorized Service Center.
ENGLISH
60 Hz
110 V 2,97 kVA
220 V 8,80 kVA
3