Microwave Power Settings; Setting The Microwave; 1, 2, 3 Series Of Operations; Ovenware - NEFF C57W40N3 Instrucciones De Uso

ovenware with decorative gold or silver trim if the manufacturer
guarantees that they are suitable for use in microwaves.
Unsuitable ovenware
Metal ovenware is unsuitable. Metal does not allow microwaves
to pass through. Food in covered metal containers will remain
cold.
Caution!
Creation of sparks: metal – e.g. a spoon in a glass – must be
kept at least 2 cm from the oven walls and the inside of the
door. Sparks could destroy the glass on the inside of the door.
Ovenware test
Do not switch on the microwave unless there is food inside. The
following ovenware test is the only exception to this rule.
Perform the following test if you are unsure whether your
ovenware is suitable for use in the microwave:
Heat the empty ovenware at maximum power for ½ to
1.
1 minute.
Check the temperature occasionally during that time.
2.
The ovenware should still be cold or warm to the touch.
The ovenware is unsuitable if it becomes hot or sparks are
generated.

Microwave power settings

Use the button to set the desired microwave power.
90 W for defrosting delicate foods
180 W for defrosting and continued cooking
360 W for cooking meat and heating delicate foods
600 W for heating and cooking food
1000 W for heating liquids
Notes
When you press a button, the selected power lights up.
■
The microwave power can be set to 1000 watts for a
■
maximum of 30 minutes. With all other power settings a
maximum cooking time of 1 hour 30 minutes is possible.

1, 2, 3 series of operations

You can use the series of operations function to set up to three
different consecutive settings and then start.
In this section, you can find out how to set a series of
operations.

Ovenware

Always use microwave-safe, heat-resistant ovenware.

Setting a series of operations

Requirement: switch on the main switch. Your appliance is
ready for operation and the
Press the button.
°±²
1.
The ° for the first operation in the series lights up.
Set the first microwave power setting and cooking time.
2.
Press the °±² button again.
3.
The for the second operation in the series lights up.
±
Set the second microwave power setting and cooking time.
4.
Press the button again.
°±²
5.
The lights up for the third operation in the series.
²
Set the third microwave power setting and cooking time.
6.
24
button lights up
~

Setting the microwave

Example: microwave power 600 W, cooking time 10 minutes.
Press the main switch.
1.
The appliance is ready for operation and the
up.
Press the button for the microwave power setting you require.
2.
The selected power setting lights up and a suggested
cooking time is displayed.
Set the cooking time using the rotary selector.
3.
Press the ƒ button.
4.
The operation starts. The cooking time starts counting down.
The cooking time has elapsed.
A signal sounds. The microwave operation has finished. You
can stop the audible signal by pressing the
off with the main switch or make new settings.
Opening the appliance door during operation
Operation is suspended. The cooling fan may continue to run.
After closing the door, press the
continue.
Changing the cooking time
Change the cooking time using the rotary selector.
Changing the microwave power setting
Press the button for the new microwave power setting. Use the
rotary selector to set the cooking time and restart.
Cancelling operation
Press and hold the „ button for a few seconds and switch off
the main switch
Notes
When you make settings, the highest microwave power
■
setting always appears as the default.
If you open the appliance door during cooking, the fan may
■
continue running.
Press the ƒ button.
7.
The operation starts. In the clock display, the total cooking time
is displayed and the currently activated operation is lit.
The cooking time has elapsed
A signal sounds. The series of operations is finished. To stop
the signal, press the button. Switch off or reset the
„
appliance.
Opening the appliance door during operation
Operation is suspended. The cooling fan may continue to run.
After closing the door, press the
continue.
Changing the setting
Changes can only be made before operation begins. Press
the button to go to the desired setting, and make the
°±²
changes.
Cancelling operation
Press the illuminated button for the set microwave power
setting. Make new settings or switch off the appliance.
symbol lights
~
button. Switch
ÁÀ
button. Operation will then
ƒ
button. Operation will then
ƒ