Technical Data - Moretti Forni R14E Manual De Instrucciones

1

TECHNICAL DATA

1.1 DESCRIPTION OF THE APPLIANCE
The oven is fitted with a baking chamber heated by means of two
heating elements, and is fitted with a removable, rotating tray holder
carriage. The baking chamber is made of steel plate, with a
programmable electronic type temperature regulation system. It is
fitted with a temperature safety thermostat, a device to spray water
and produce steam with a timer, a suction fan that can remove fumes
both from the baking chamber and from the hood, and a glazed door
with locking handle. Cooking is extremely even thanks to the
adjustable deflectors controlling the hot air ventilation cycles and
flow, combined with rotation of the carriage.
1.2 DIRECTIVES APPLIED
This appliance complies with the following directives:
- Low Voltage Directive2014/35/EU (pursuant to 2006/95/EC)
- Directive EMC 2014/30/EU (pursuant to 2004/108/C E)
1.3 WORKPLACES
The oven is programmed by the operator using the control panels at
the front, and it must be attended to while in operation.
The door giving access to the oven is located at the front.
1.4 MODELS
The following models are available:
ROTOR14
1.5 TECHNICAL DATA (See Tab.1)
1.6 WORKING DIMENSIONS - WEIGHTS (See Fig.1).
1.7 IDENTIFICATION
When communicating with the manufacturer or service centre,
always give the oven SERIAL NUMBER, which is affixed to the
bottom right hand part of the appliance as indicated (See Fig. 2).
1.8 LABELLING
The oven is provided with warning labels at the points indicated in
fig. 3.
WARNING!
On the equipment surface there is a burn risk
due to high temperature elements. For any intervention or action wait
for the appliance to cool to room temperature and always use suitable
protective equipment (gloves, glasses...).
WARNING!
Presence of dangerous tension. Before
performing any maintenance operation, disconnect the power supply
by turning off the switches fitted on the outside of the oven and/or
the leavening compartment and wait for the appliance to cool to
room temperature. Always use suitable protective equipment (gloves,
glasses...).
WARNING!
To avoid scalding, do not use loaded containers
with liquids or cooking goods which becomes fluid by heating in
higher levels than those which can be easily observed.
WARNING!
The label referred to above dates is provided
and it is mandatory position them to a 1.6 m height from the floor is
in the oven in the cart (see Figure 3).
WARNING!
Moving parts.
WARNING!
Slippery floor.
1.9 ACCESSORIES
The oven is equipped with the following accessories:
- Rotating carriage
1.10 NOISE
This appliance is a technical instrument of work and normally, the
noise level threshold at the operator station does not exceed 74 dB
(A).
2 INSTALLATION
NOTE:
the manufacturer declines all responsibility in the
event of failure to comply with safety regulations.
2.1 TRANSPORT
The oven is generally delivered wrapped in a transparent synthetic
film and mounted on wooden pallets, using road transport vehicles
(See Fig. 4).
2.2 UNLOADING
NOTE:
on receiving the oven, it is advisable to check its
conditions and quality.
Raise the equipment using only and exclusively the points indicated
at the pict. 5, after removing the lids as shown.
After unloading and replacing the 4 fastening elements, it is easy to
position the appliance because it is fitted with rollers underneath.
Position the oven in a suitably hygienic, clean, dry and dust-free area,
making sure that it is stable. Packing materials must be disposed of in
accordance with current regulations.
2.3 ENVIRONMENTAL SPECIFICATIONS
To ensure that the oven operates properly, it is advisable to comply
with the following limits:
Working temperature: + °5C ÷ + °40C
Relative humidity: 15 % ÷ 95 %
2.4 POSITIONING, ASSEMBLING AND MAINTENANCE
AREAS
WARNING!
the oven, the following specifications have to be complied with:
- Laws and standards in force regarding the installation of
electrical appliances.
- Directives and indications issued by the electricity supply
network.
- Local building and fire-prevention laws.
- Accident prevention regulations.
- Regulations in force of the electromechanical rules.
Remove the protective film from the outside of the oven, pulling it
gently to remove all the adhesive. Should any adhesive remain on the
oven, remove using kerosene or benzene.
UK2
When positioning, assembling and installing