Wayne Dalton 8000 Manual Del Usuario página 20

17
Attaching Adjustable Flagangle
to Q.I./Universal Horizontal Track
NOTE: If quick install flagangles were used in step
Tools Needed:
16, skip this step and continue with step 18. If not,
9/16" Socket
complete this step.
7/16" Socket
Ratchet Wrench
To install horizontal track, place the curved end over
the top roller. Align the bottom of the horizontal track
9/16" Wrench
with the vertical track. Hand tighten the horizontal
Level
track to the flagangle with (2) 1/4"- 20 x 9/16" track
Hammer
bolts (or stud plate) and (2) 1/4"- 20 flange hex nuts.
Flat Tip
WARNING
Screwdriver
Step Ladder
DO NOT RAISE DOOR UNTIL HORIZONTAL TRACKS
ARE SE CURED AT REAR, AS OUTLINED IN STEP 29,
OR DOOR COULD FALL FROM OVERHEAD POSITION
CAUSING SEVERE OR FATAL INJURY.
Level the horizontal track assembly and bolt the
horizontal angle to the slot in the flagangle using (1)
3/8"- 16 x 3/4" truss head bolt and (1) 3/8"- 16 hex
nut. Repeat for other side. Remove the nail that was
temporarily holding the top section in place, installed
in Step 15.
IMPORTANT: Failure to remove nail before attempting
to raise door could cause permanent damage to top
section.
NOTE: If an idrive
horizontal tracks slightly above level.
NOTE: After completing this step, continue with Step
18.
18
Adjusting Top Brackets
With horizontal tracks installed you can adjust the
Tools Needed:
top brackets. Vertically align the top section with the
7/16" Wrench
lower sections. Once aligned, position the top roller
1/2" Wrench
in the adjustable slide(s), out against the horizontal
Step Ladder
track.
Tape Measure
FOR WINDLOAD OPTION CODES (A): 1100 OR 1120:
Maintaining the slide's position, tighten the (1) 1/4"
- 20 nut to secure the slide to the top bracket. Repeat
for other side.
FOR WINDLOAD OPTION CODES (B): 1101, 1102,
1103, 1104, 1121, 1122, 1123, 1140, 1141 OR 1143:
Maintaining the slide's position, tighten the (1) 5/16"
- 18 nut to secure the slide to the top bracket base.
Now lock the slide in position using (1) 1/4" - 20 x
9/16" track bolt and (1) 1/4" - 20 hex nut through
any aligning hole. Repeat for other side.
FOR WINDLOAD OPTION CODES (C): 1124, 1125,
1142 or 1144: Maintaining the slide's position,
tighten the (2) 5/16" - 18 nuts to secure the slides to
the top brackets. Now lock the top slides in position
using (2) 1/4" - 20 x 9/16" track bolts and (2) 1/4"
- 20 hex nuts through any two aligning holes. Repeat
for other side.
NOTE: If you have windload option codes 1121, 1122,
1123, 1124, 1125, 1141 and 1142, pushnuts are
required to be installed.
IMPORTANT: ACCURATELY POSITIONING THE
PUSHNUT ONTO THE ROLLER STEM IS CRITICAL.
ONCE THE PUSHNUT IS PUSHED ONTO THE ROLLER
STEM, THE TABS MAKING CONTACT WITH THE STEEL
SURFACE, WILL MAKE IT DIFFICULT TO REPOSITION
THE PUSHNUT.
20
Please Do Not Return This Product To The Store. Contact your local Wayne Dalton dealer. To find your local Wayne Dalton dealer, refer to your local
yellow pages business listings or go to the Find a Dealer section online at www.Wayne-Dalton.com.
opener will be installed, position
®
Flagangle
Q.I. horizontal
track
(1) Stud
plate
(2) 1/4"- 20
Universal
Flange hex
horizontal
nuts
track
(1) 3/8"- 16
Hex nut
Top section
(1) 5/16" - 18
Nut
Top bracket
slide
Short shaft
roller
Correct
(A)
Top bracket
assembly's
Top bracket
slide
Top section
Long shaft
roller
Incorrect
Flagangle
Universal
horizontal
track
(2) 1/4"- 20 X 9/16"
Universal
(2) 1/4"- 20
horizontal
Flange hex
track
nuts
Flagangle
(1) 3/8"- 16 X 3/4"
Truss head bolt
Horizontal angle
(1) 1/4" - 20 X 9/16" Track bolt
and (1) 1/4" - 20 flanged hex nut
Horizontal
(1) 5/16" - 18
track
Nut
Short shaft
roller
Top bracket
slide
Top section
(B)
(2) 1/4" - 20 X 9/16" Track
bolts and (2) 1/4" - 20 flanged
hex nuts
Horizontal
track
Top bracket
(2) 5/16" - 18
Nuts
(C)
Track bolts
Horizontal
track
slide