Electrical Safety - DeWalt DW712 Traducido De Las Instrucciones Originales

E NGL IS H
• Check for damage to the tool, parts or accessories which may
have occurred during transport.
• Take the time to thoroughly read and understand this manual prior
to operation.
Description (Fig. A1–A6)
WARNING: Never modify the power tool or any part of it.
Damage or personal injury could result.
A1
1 On/off switch
2 Moveable lower guard
3 Fence left-hand side
4 Mitre lever
5 Mitre latch
6 Mitre scale
7 Fixed fence
8 Fence right-hand side
9 Bevel position adjustment stop
10 Bevel scale
11 Bevel clamp handle
12 Grooving stop
13 Rail lock knob
14 Head lock down pin
15 Grooving depth adjustment knob
16 Spindle lock button
17 Head lock up release lever
18 Operating handle
19 Speed control dial (DW712)
A2
23 Upper guard
24 Dust spout
25 Rails
26 Blade spanner
27 Bevel stop override knob
28 Vertical position adjustment stop
29 Upper fence left-hand side clamping knob
30 Hand indentation
31 Kerf plate
32 Date code
OPTIONAL ACCESSORIES
A4
35 Legstand
A5
36 Dust extraction kit
A6
37 Carrying strap
INTENDED USE
Your D WALT DW712 Mitre Saw has been designed for professional
e
cutting wood, wood products and plastics. It performs the sawing
operations of cross-cutting, bevelling and mitring easily, accurately and
safely.
This unit is designed for use with a nominal blade diameter 216 mm
carbide tip blade.
DO NOT use under wet conditions or in presence of flammable liquids
or gases.
These miter saws are professional power tools.
DO NOT let children come into contact with the tool. Supervision is
required when inexperienced operators use this tool.
30
WARNING! Do not use the machine for purposes other
than intended.
• Young children and the infirm. This appliance is not intended for
use by young children or infirm persons without supervision.
• This product is not intended for use by persons (including children)
suffering from diminished physical, sensory or mental abilities; lack
of experience, knowledge or skills unless they are supervised by
a person responsible for their safety. Children should never be left
alone with this product.

Electrical Safety

The electric motor has been designed for one voltage only. Always
check that the power supply corresponds to the voltage on the rating
plate.
Your tool is double insulated in accordance with EN61029;
therefore no earth wire is required.
In case of cord replacement the tool must only be repaired by an
authorized service agent or by qualified electrician.
Mains Plug Replacement
(U.K. & Ireland only)
If a new mains plug needs to be fitted:
• Safely dispose of the old plug.
• Connect the brown lead to the live terminal in the plug.
• Connect the blue lead to the neutral terminal.
WARNING: No connection is to be made to the earth
terminal.
Follow the fitting instructions supplied with good quality plugs.
Recommended fuse: 13 A.
Using an Extension Cable
If an extension cable is required, use an approved 3–core extension
cable suitable for the power input of this tool (see Technical Data).The
minimum conductor size is 1.5 mm
2
When using a cable reel, always unwind the cable completely.
Installation
UNPACKING (FIG. B)
• Remove the saw from the packing material carefully.
• Release the rail lock knob (13), and push the saw head back to
lock it in the rear position.
• Press down the operating handle (18) and pull out the lock down
pin (14), as shown.
• Gently release the downward pressure and allow the head to rise to
its full height.
BENCH MOUNTING (FIG. C)
• Holes (40) are provided in all four feet to facilitate bench mounting.
Two different sized holes are provided to accommodate different
sizes of bolts. Use either hole; it is not necessary to use both. Bolts
with a diameter of 8 mm and 80 mm in length are suggested.
Always mount your saw firmly to prevent movement. To enhance
the portability, the tool can be mounted to a piece of 12.5 mm or
thicker plywood which can then be clamped to your work support
or moved to other job sites and reclamped.
• When mounting your saw to a piece of plywood, make sure that
the mounting screws do not protrude from the bottom of the wood.
The plywood must sit flush on the work support. When clamping
the saw to any work surface, clamp only on the clamping bosses
where the mounting screw holes are located. Clamping at any
other point will interfere with the proper operation of the saw.
• To prevent binding and inaccuracy, be sure the mounting surface is
not warped or otherwise uneven. If the saw rocks on the surface,
place a thin piece of material under one saw foot until the saw is
firm on the mounting surface.
; the maximum length is 30 m.