Legal Notices & Regulatory Information - Elcometer 480 Guia Del Usuario

18 LEGAL NOTICES & REGULATORY INFORMATION
The Elcometer 480 Model T meets the Radio and Telecommunications Terminal Equipment Directive.
The Elcometer 480 Model B meets the Electromagnetic Compatibility Directive.
This product is Class B, Group 1 ISM equipment according to CISPR 11. Class B product: Suitable for use in
domestic establishments and in establishments directly connected to a low voltage power supply network which
supplies buildings used for domestic purposes. Group 1 ISM product: A product in which there is intentionally
generated and/or used conductively coupled radiofrequency energy which is necessary for the internal
functioning of the equipment itself.
The USB is for data transfer only and is not to be connected to the mains via a USB mains adapter.
The ACMA compliance mark can be accessed via: Menu/About/Legal/Regulatory.
Elcometer 480 Model T: The Giteki mark, its ordinance number and Bluetooth SIG QDID can be accessed via:
Menu/About/Legal/Regulatory
Elcometer 480 Model T: This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any
interference received, including interference that may cause undesired operation.
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. End users
must follow the specific operating instructions for satisfying RF exposure compliance. This transmitter must not be
co-located or operating in conjunction with any other antenna or transmitter.
Changes or modifications not expressly approved by Elcometer Limited for compliance could void the user's
authority to operate the equipment.
Elcometer 480 Model B: NOTE: This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television reception, which can
be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected
-- Consult the dealer or an experienced radio/TV technician for help.
Elcometer 480 Model T: Under Industry Canada regulations, this radio transmitter may only operate using an
antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce
potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent
isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication.
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following
two conditions: (1) this device may not cause interference, and (2) this device must accept any interference,
including interference that may cause undesired operation of the device.
Elcometer 480 Model B: This Class B digital apparatus complies with Canadian ICES-003.
and ElcoMaster are registered trademarks of Elcometer Limited, Edge Lane, Manchester,
R
M43 6BU. United Kingdom
are trademarks owned by Bluetooth SIG Inc and licensed to Elcometer Limited.
Elcometer 480 Model T: Made for iPhone 6 Plus, iPhone 6, iPhone 5s, iPhone 5c, iPhone 5, iPhone 4s, iPhone 4,
iPad Air 2, iPad mini 3, iPad Air, iPad mini 2, iPad (3rd and 4th generation), iPad mini, iPad 2, and iPod touch (4th
and 5th generation).
"Made for iPod," "Made for iPhone," and "Made for iPad" mean that an electronic accessory has been designed to
connect specifically to iPod, iPhone, or iPad, respectively, and has been certified by the developer to meet Apple
performance standards. Apple is not responsible for the operation of this device or its compliance with safety and
regulatory standards. Please note that the use of this accessory with iPod, iPhone, or iPad may affect wireless
performance.
iPad, iPhone, and iPod touch are trademarks of Apple Inc., registered in the U.S. and other countries.
App Store is a trademark of Apple Inc., registered in the U.S. and other countries.
Google Play is a trademark of Google Inc.
All other trademarks acknowledged.
en-29
R
®
www.elcometer.com