Malfunctions - Porsche Mobile Charger Plus Manual De Funcionamiento E Instrucciones De Instalación

Operating instructions
US Information
The security field contains the personal unlocking key
(PUK). This field has special ink covering the PUK.
FC
The PUK is only visible when this field is dampened
under running water. Do not rub or scratch the field
while dampening it, as this could damage the PUK.
ESM
Password for web application
The password is used for logging into the web
PTB
application.
When using the initial password:
e If you lose or forget the initial password,
TR
contact an authorized Porsche dealer.
When using a password you set yourself:
e If you lose your password, you can restore the
RU
initial password using the PUK, or contact an
authorized Porsche dealer.
UK
e Resetting the charger to its factory settings
reactivates the initial password. This also resets
all of the charger's settings to the factory
VIE
settings, however.
f Please see chapter "Privat mode/Open mode" on
HE
page 16.
Serial number of the charger
AR The serial number of the charger can be found in the
following places:
– In the letter containing access data, after the
JPN
designation Serialnumber
– On the identification plate (on the back of the
control unit), after the abbreviation SN
KOR
– In the web application: Settings > Maintenance >
Device information
CHT
THA
16
Privat mode/Open mode
On delivery, the charger is configured to be in open
mode. This means that the energy manager is
automatically found and connected in the home
network.
We recommend only switching to private mode after
you have started up the device for the first time.
Activating private mode
1. In the web application, navigate to Connections >
Energy manager.
2. Activate Private mode.
To connect the energy manager in private mode,
you must confirm this in the web application.
f Please see chapter "Connecting in the charger's
web application" on page 15.
Resetting to the factory settings
Activating this function will delete all your settings.
In addition, all passwords will be set to the initial
passwords in the letter containing access data.
Information
This function is deactivated in the charger by default.
In order to execute this function on the charger, you
need to enable it in the web application (Settings >
System > Activate reset to factory settings).
C
1. Simultaneously press the
HARGE STATUS
M
and the
ULTIFUNCTION BUTTON
least 5 seconds.
C
At the same time, the
HARGER
flashes white.
C
2. As soon as the light indicator stops
HARGER
M
flashing, release the
ULTIFUNCTION BUTTON
C
but continue holding the
HARGE STATUS
for another 2 seconds.
3. Press and hold the
again for 5 seconds.
At the same time, the
flashes white.
The charger is reset to the factory settings.
At the same time, the light indicators light up
green.
When the self-test has successfully been
completed, the charger is ready for operation.
A reset to factory settings is also possible using the
web application or at an authorized Porsche dealer.
Porsche recommends an authorized Porsche dealer,
as they have trained technicians and the necessary
parts and tools.
f For notes on the web application, see the
instructions at https://www.porsche.com/
international/aboutporsche/e-performance/
help-and-contact/.
For other languages, select the desired country
version of the website.

Malfunctions

The charger indicates faults or malfunctions by light
indicators that light up or flash red or yellow.
NOTICE
e If a fault persists or recurs, disconnect the charger
button
from the power grid and contact a qualified
and hold for at
electrician. Porsche recommends an authorized
Porsche dealer, as they have trained technicians
light indicator and the necessary parts and tools.
f Please see chapter "Control unit" on page 10.
,
button
M
ULTIFUNCTION BUTTON
C
light indicator
HARGER
Damage to the charger