Stiga BC 636 Serie Manual De Instrucciones página 145

WARNING!: READ THIS MANUAL CAREFULLY BEFORE
EN
USING THE MACHINE. Keep safe for future use.
INDICE
1. GENERAL INFORMATION ..................................... 1
2. SAFETY REGULATIONS ........................................ 2
3. ABOUT THE MACHINE .......................................... 4
3.1 Machine description and intended use ........... 4
3.2 Safety signs .................................................... 5
3.3 Product identification label ............................. 5
3.4 Main components ........................................... 6
4. ASSEMBLY ............................................................. 6
4.1 Assembly components ................................... 6
4.2 Grip assembly ................................................ 7
4.3 Selecting the cutting means and specific guard
....................................................................... 7
4.4 Fitting the guard on the cutting means............ 7
4.5 Fitting and removing the cutting means ......... 8
4.6 Mounting the flexible drive-shaft tube ............. 8
5. CONTROLS ............................................................ 9
5.1 Engine start / stop switch ................................ 9
5.2 Throttle control lever ....................................... 9
5.3 Throttle safety lever ........................................ 9
5.4 Manual starting grip ........................................ 9
5.5 Choke control lever (if available) ..................... 9
5.6 Primer control button ...................................... 9
5.7 Display (if available) ....................................... 9
6. USING THE MACHINE ........................................... 9
6.1 Preliminary operations.................................. 10
6.2 Safety checks ............................................... 10
6.3 Start-up ........................................................ 11
6.4 Operation ..................................................... 12
6.5 Advice for operation ..................................... 13
6.6 Stop.............................................................. 13
6.7 After use ....................................................... 13
7. ROUTINE MAINTENANCE ................................... 13
7.1 General Information ...................................... 13
7.2 Preparing the fuel blend ............................... 14
7.3 Refuelling ..................................................... 14
7.4 Cleaning the machine and the engine .......... 14
7.5 Nuts and bolts .............................................. 15
8. OCCASIONAL MAINTENANCE ........................... 15
8.1 Angle transmission lubrication: ..................... 15
8.2 Flexible drive-shaft lubrication ...................... 15
8.3 Cleaning the air filter..................................... 15
8.4 Spark plug ................................................... 15
8.5 Cutting means maintenance ......................... 15
8.6 Sharpening the wire cutting blade ................ 16
8.7 Adjusting idle speed ..................................... 16
8.8 Carburettor ................................................... 16
9. STORAGE ............................................................. 16
10. HANDLING AND TRANSPORT ............................ 17
11. ASSISTANCE AND REPAIRS ............................... 17
13. MAINTENANCE TABLE ........................................ 18
14. TROUBLESHOOTING ......................................... 19
1. GENERAL INFORMATION
1.1 HOW TO READ THIS MANUAL
Some of the paragraphs in this manual contain
particularly important information in terms
of safety and operation, and are highlighted
differently, according to the following criteria:
NOTE or IMPORTANT These give details
or further information on what has been
previously indicated and aim to prevent damage
to the machine or cause other damage.
The symbol represents a danger. Failure
to observe the warning can lead to possible
personal and/or third party injury and/or damage.
The paragraphs highlighted in a dotted grey
square indicate optional characteristics
not available on all models documented
in this manual. Check if the characteristics
are available on this model.
Whenever reference is made to a position on the
machine "front", "back", "left" or "right" hand side,
this refers to the operator's working position.
1.2 REFERENCES
1.2.1 Figures
The figures in these instructions for
use are numbered 1, 2, 3, etc.
Components shown in the figures
are marked A, B, C, etc.
Reference to component C in figure
2 is indicated with the wording: "See
fig. 2.C" or simply "(Fig. 2.C)".
The figures are provided by way of
example. The actual pieces can differ from
those illustrated in this document.
1.2.2 Titles
The manual is arranged in chapters and
paragraphs. The title of paragraph '2.1 Training" is
a sub-title of "2. Safety regulations". References
to titles or paragraphs are marked with the
abbreviation chap. or par. and the relevant
number. Example: "chap. 2" or "par. 2.1.
EN - 1