Publicidad
Idiomas disponibles
Idiomas disponibles
The rinsing will start working of by the reached
temperature need. That means the period of the
washing cycle you chosed will be extended up to
having reached the exact temperature.
G
– Extracting the basket inclines and shakes it
carefully. So the rest of the water drops will be
eliminated.
Leave the dishes in the basket until its will be dry
by evaporation. Take the dishes away from the
basket and pay attention not to touch the dishes
on its border and put the on clean shelves.
To continue carry a new basket, introduce it in
the machine, close the door and press button
"C".
Endless cycle (maximum 15 minutes) : the door
-
being closed and the cycle put on (any cycle), keep the
button "B" pressed for 3 seconds: lamps 1 and 2 will
flash at the same time (thermocontrol excluded); the
cycle can be interrupted at any time pressing again
button "C" that will let final sequences start.
Self-washing cycle: with machine on, carry out
the following operations:
-
Remove the overflow from the tank and
wait for the tank's emptying (for machines
with drain pump, look at the instructions in
the specific paragraph),
-
Close the door of the glasshwasher,
-
Keep pressed the cycle button ''C'' during
3 seconds: lamp ''2'' flashes during all the
length of the 5 or 10 minutes cycle,
according to the rinse's duration fixed by
default.
ACHIEVEMENTS
Any deficiency in the washing process is
apparent when dirty residuals are visible. An
insufficient rinsing might cause any halos: in this
case, check that the rinsing jets are clean and
there is a sufficient pressure in the water
distribution network.
In the case that residuals are present, check
that:
• the washing jets are clean
• there is detergent
• the pump suction filter is clean
• the positions of the objects in the rack are
correct.
REGENERATING
(for machines with Water softener)
If the glass-washer is equipped with a Water softener
the regeneration of resins is automatic according to
parameters fixed by the producer.
According to the water hardness, it is possibile to
modify the programming of the regeneration. See the
corresponding table in the installer section.
N.B. each 90 seconds of tank filling
duration, the machine stops for about
2
minutes
regeneration.
SALT CONTROL
When it is necessary to add salt in the container, the
green lamp "E" is flashing.
Unscrew the plug of the salt container at the bottom of
the tank and put 1 kg coarse salt tablets in it. Clean the
gasket and screw the plug.
Attention!
The lack of salt in the container damages the machine
because of limestone, besides a defective washing of
glasses and dishes.
These damages are not covered by the warranty.
GLASSES POSITIONING
In order to obtain a successful dishwashing, it is
suitable to take care of the way dishes are
placed. It is suitable to place glasses, inside the
wire basket with the concave side towards the
bottom. Place mixed cutlery in a vertical position
into the suitable container minding not to cram
them and with hafts towards the bottom (see the
drawing).
DRAIN PUMP INSTRUCTION
(only for machines with drain pump)
The drain pump starts up automatically just
during the washing cycle to discharge the
exceeding water coming from the rinsing cycle.
At the end of the working day, in order to
completely discharge the tank, it is necessary
to perform the following operations:
1. Open the door of the dishwasher
2. Remove the overflow pipe from the tank;
3. Afterwards push button "F" for 3 seconds.
Alternatively are flashing the control lamp "E" and
the cycle lamp (chosen before)
The discharge will stop automatically after 5
minutes. The control lamps will stop flashing.
The drain can be stopped at any time by pressing
again button ''F'' .
Please note: in case the door is open the control
lamp "E" will continue flashing.
Reinstall the flow over and shut the door.
26
to
carry
out
the
Publicidad
