Publicidad
Idiomas disponibles
Idiomas disponibles
EN WA-200SP - WA-200FT INTEGRA | WIDER1A - WIDER1A R
When replacing fluid nozzle set (2-1) and fluid needle set (2-2), check the correct coupling
of both, in order to avoid any paint leakage from the fluid nozzle during spray gun operation.
To adjust the fluid adjustment set (9), turn the adj. knob of the fluid adjustment
set. The standard for the fully closure of the paint adjustment device requires that the
gap between the guide and the knob is: 2 mm for the WIDER1A and 1 mm for the
WA-200SP & WA-200FT INTEGRA.
During the adjustment it is recommended not to over-tighten the adjustment too much as its
excessive tightening could cause deformation of the fluid nozzle.
5.4 INSPECTION & REPLACEMENT STANDARD
WHERE TO INSPECT
Each hole passage of air cap (1)
Replace if it is crushed or deformed.
and fluid nozzle (2-1).
Packing and O ring.
Replace if it is deformed or worn out.
Leakage from seat section betwe-
Replace them if leakage does not stop after fully clea-
en fluid nozzle (2-1) and fluid needle
ning fluid nozzle (2-1) and fluid needle set (2-2). If you
set (2-2).
replace fluid nozzle (2-1) or fluid needle set (2-2) only,
fully match them and confirm that there is no leakage.
6. TROUBLESHOOTING
PROBLEM
GUN DOES NOT SPRAY
Fluid adj. knob (9) closed.
Tip hole of fluid nozzle (2-1) obstructed.
Deposit of paint between the fluid needle (2-2)
and the needle packing set (11).
INTERMITTENT SPRAY PATTERN
Air escapes from fluid nozzle (2-1) and the conical
seats of the gun body.
Air escapes from fluid needle packing (11).
Air escapes from fluid hose joint.
Dirty inside air cap set (1).
DEFECTIVE SPRAY PATTERN
Dirty nozzle (2-1) or air cap set (1).
Nozzle (2-1) or air cap (1) has been damaged.
Fluid nozzle (2-1) is loose.
Paint viscosity too high or too low.
Fluid output too high or too low.
LEAKING
Fluid nozzle (2-1), fluid needle set (2-2) or gun
body, dirty, damaged or worn on seat.
Loose fluid adj. knob (9).
Fluid needle spring set (7) is worn.
Loose fluid nozzle set (2-1).
Needle packing set (11) loose, too tight, dirty
or worn.
Piston set (6-1) dirty, damaged, worn on seat.
Piston spring (8) is worn.
Piston packing (6-2) is worn.
6
REPLACEMENT PART
REMEDY
Check and adjust it.
Check and clean it.
Check and clean it.
Check , clean or replace.
Tighten.
Tighten.
Clean.
Clean carefully.
Replace if damaged.
Tighten.
Dilute paint or increase
viscosity.
Adjust fluid adj. knob (9)
to reduce or increase.
Check , clean or replace.
Adjust.
Replace.
Tighten.
Adjust, clean or replace.
Clean or replace.
Replace.
Replace.
WA-200SP - WA-200FT INTEGRA | WIDER1A - WIDER1A R
7. SPARE PARTS LIST
1R
3
1-2R
1-1R
2-1
1
12
1-2
1-1
3-1
16
15
13
POS. DESCRIPTION
1
AIR CAP SET
1R
AIR CAP SET (WIDER-1AR)
1-1 AIR CAP COVER RING
1-2 AIR CAP PACKING
•
2-1 FLUID NOZZLE SET
2-2 FLUID NEEDLE SET
•
3
BODY SET
3-1 AIR NIPPLE
4
PATTERN ADJUSTMENT
4R
PLUG (WIDER-1AR)
5
AIR VALVE SEAT
•
5-1 O RING
6-1 PISTON
•
6-2 PISTON PACKING
7
NEEDLE SPRING
8
PISTON SPRING
9
FLUID ADJUSTMENT KNOB
10
FIXING BOLT
11
NEEDLE PACKING SET
•
12
PROTECTION COVER
13
BRUSH
15
HALF UNION FOR Ø 6 (CYL)
16
HALF UNION FOR Ø 8 (CAP)
•
Marked parts are wearable parts
NEVER REMOVE FLUID NIPPLE FROM GUN BODY! Any malfunctions resulting by the
removal of this parts will not be covered by the Warranty. In case of replacement contact
your Technical Service directly.
When ordering parts, specify gun model, part name with No. and marked No. of air cap
set, fluid nozzle and fluid needle.
4R
4
11
5
6-1 6-2
5-1
2-2
7
9
8
WA-200 INTEGRA
10
WIDER1A
NOZZLE_NEEDLE SET COMBINATION
Fluid Nozzle set
Needle set
ø mm (in)
Mark
Mark
0.8 (0.031)
W1/08
12H WIDER1A
1.0 (0.039)
W1/10
1.3 (0.051)
W1/13
15H WIDER1A
1.5 (0.059)
W1/15
0.5 (0.020)
W1/05
05H WIDER1A
0.8 (0.031) W2-2/V8-08
1.0 (0.039) W2-2/V8-10
12H WIDER1A
1.2 (0.047) W2-2/V8-12
1.4 (0.055) W2-2/V8-14
15H WIDER1A
1.6 (0.063) W2-2/V8-16
0.6 (0.024)
W2/06
0.8 (0.031)
W2/08
12H WIDER1A
1.0 (0.039)
W2/10
1.2 (0.047)
W2/12
1.5 (0.059)
W2/15
15H WIDER1A
2.0 (0.079)
W2/20
20H WIDER2A
2.5 (0.098)
W2/25
25H WIDER2A
EN
9
7
Publicidad
