Descargar Imprimir esta página

Wolf Garten A 370 E Instrucciones De Funcionamiento Originales página 23

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 99
Operation
Put the washer Ag on the screw from the other
Î
side G 3.
Insert the threaded pin Aj into the quick-release
Î
levers Ad, so that the hole is visible G 2. Hold
this tightly with finger and thumb and screw in the
quick-release lever together with the threaded pin
in a clockwise direction G 3 until there is a gap of
approximately 10 mm G 4.
Fasten the upper part of the handlebar, by folding
Î
down the left and right quick-release levers G 5.
Note
Depending on your height, you can select an
operating position for comfortable mow-
ing U I/II/III by releasing the two bottom
quick release levers U 1 and changing the
inclination of the assembled handle until
the desired height is obtained U 2. Once
the handle is set to the desired height, snap
the bottom quick release levers back up
again U 3.
To secure the power cable to the lawnmower,
Î
lead it through the anti-kink protector and attach
it with a cable clip Af at the indicated point H
(see arrow).
Note
Ensure that the cable is not kinked.
Take the strain-relief device Ab and attach it with
Î
the large opening on the WOLF-Garten Flick-
Flack® bracket Ac / I 1
Finally insert the WOLF-Garten Flick-Flack®
Î
bracket into the two eyes on the left and right
sides of the bottom part of the handle I 2.
Note
To simplify transport and storage, you can
fold the handle together. See "Transport and
storage" for more detailed information.
Assembling the grass collector (Fig. J K L)
Grip the frame with one hand on the handle J 1
Î
and use the other hand to pull the fabric collection
bag over the long end of the frame J 2. Guide
the fabric collection bag through with its profile
section under the handle and attach the profile
section of the bag to the frame under the handle
J 3 .
Then fasten the side profile sections of the bag on
Î
to the frame, see K 1 - 3.
Then turn the grass collector upside down and
Î
attach the profile sections, see L 1 - 2.
Operation
Operating elements (Fig. Z)
1 Handle
2 Operator presence control
3 Wolf-Garten Flick-Flack® bracket
4 Grass collector
5 Fill level indicator
6 Deflector flap
7 Handle height adjuster
8 Cutting height adjuster
9 Power cable connector
10 On/off switch (switch-on preventer)
11 Cable strain-relief device
12 Anti-kink protector
13 Cutting height indicator
14 Changeover switch (cut-collect/mulch)
15 Mower blade
Operating times
Observe the times stipulated in local byelaws.
Î
Check with your local authorities to determine if
Î
there are any operating time limitations.
Strain-relief device (Fig. M N)
Guide the cable into the strain-relief device as
Î
shown in M 1. The way in which the cable is
fastened, depends on its diameter.
Note
The WOLF-Garten Flick-Flack® bracket
holds the cable away from the cutting mech-
anism M 2+ N.
Attaching the grass collector (Fig. O)
Risk of injuries due to the rotating mower
blade.
¾ Switch the motor off. Wait until the motor
blade comes to a standstill, and pull out
the mains plug before you make any
adjustments to the device.
Raise the deflector flap O 1.
Î
Hold the grass collector by its handle and tilt it
Î
slightly, so that the grass collector can be attached
by its hooks in the recesses on the rear side of the
lawnmower O 2.
Hook the grass collector on to the lawnmower O
Î
2.
Fold the deflector flap downwards again O 3.
Î
DANGER!
EN
23

Publicidad

loading