Publicidad
Idiomas disponibles
Idiomas disponibles
EN
Adjusting the cutting height (Fig. P)
Risk of injuries due to the rotating mower
blade.
¾ Switch the motor off. Wait until the motor
blade comes to a standstill, and pull out
the mains plug before you make any
adjustments to the device.
Pull the lever out slightly P 1.
Î
Set the desired cutting height P 2.
Î
Release the lever again P 3.
Î
Note (cutting height – grass condition)
Whenever possible, to protect the turf of the
lawn, only mow the grass when it is thor-
oughly dry.
Set a cutting height of 45 mm.
When cutting damp or long grass mow with
a higher cutting height.
Connecting to the socket (230 Volt, 50 Hz)
Attention!
Only connect the lawnmower to power outlets that
are protected by a slow 16 A fuse (or type B circuit-
breaker).
Important information about RCDs
An RCD protects you against severe injury in the
event of you coming into contact with damaged/bare
wires, if an insulation defect exists and, under cer-
tain circumstances, if damage to live wires occurs.
Only connect the lawnmower to power outlets that
Î
are protected by a residual current device (RCD)
with a tripping current of no more than 30 mA.
• For older wiring installations, upgrade kits are
available. Consult a qualified electrician.
Switching the lawnmower on/off (Fig. Q R)
Risk of injuries due to the rotating mower
blade.
¾ Do not switch the lawnmower on if you
are standing in front of the grass ejector
opening!
¾ Only switch the lawnmower on when it is
on a level surface.
Attention!
¾ Do not switch the lawnmower on in long grass -
if necessary raise it slightly, as shown in Q.
Switching the motor on (Fig. R)
Press and hold the button R 1 .
Î
Pull the operator presence control R 2 in.
Î
Release the button R 1.
Î
24
DANGER!
CAUTION!
Switching the motor off (Fig. R)
Release the operator presence control R 3.
Î
Activating the cut/collect function (Fig. O S T)
Risk of injuries due to the rotating mower
blade.
¾ Only adjust the lawnmower with the
motor switched off and the mower blade
at a standstill.
The lawnmower is equipped with a
changeover switch (cut-collect/mulch). .
Use this switch to choose between the
functions cut-collect and mulching for
your lawn care.
Raise the deflector flap T 1.
Î
Remove the grass collector T 2.
Î
Lower the deflector flap again T 3.
Î
Turn the switch to cut-collect S 1.
Î
Raise the deflector flap O 1.
Î
Hook the grass collector on O 2.
Î
Lower the deflector flap again O 3.
Î
Removing and emptying the grass collector
(Fig. T V W)
If grass cuttings are left lying on the ground or the
yellow STOP sign of the fill level indicator is visi-
ble V 2, the grass collector is full and you should
empty it immediately W 1.
Risk of injuries due to the rotating mower
blade.
¾ Switch the motor off. Wait until the motor
blade comes to a standstill, and pull out
the mains plug before you make any
adjustments to the device.
Switch the motor off and pull out the plug.
Î
Raise the deflector flap T 1.
Î
Remove the grass collector T 2.
Î
Lower the deflector flap again T 3.
Î
Empty the grass collector W 1.
Î
Before starting, clear any blockages in the mowing
Î
chamber W 2.
Filling level indicator information (Fig. V W)
The fill level of the grass collector is indicated by
Î
the position of the flap of the fill level indicator.
• If the grass collector is empty, the flap of the
indicator points upwards V 1.
• If the grass collector is full, the flap of the indica-
tor points downwards and the yellow STOP sign
is visible V 2.
DANGER!
DANGER!
Operation
Publicidad
